Parkside PBTS 370 B2 Originalbetriebsanleitung Seite 22

g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control
of the tool in unexpected situations.
5. Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool is
maintained.
m WARNING!
This power tool generates an electromagnetic field during op-
eration. This field can impair active or passive medical implants
under certain conditions. In order to prevent the risk of serious
or deadly injuries, we recommend that persons with medical
implants consult with their physician and the manufacturer of
the medical implant prior to operating the power tool.
Additional safety instructions for the belt and disc
sander
m WARNING!
Do not use your machine until it is completely assembled and
installed according to the instructions.
• Read the entire operating manual before using the device.
• Attention: This machine is designed for grinding wood or
wood-like material only. The sanding of other materials can
cause fire, injuries, or damage the product.
• Always wear safety goggles.
• This machine may only be operated indoors.
• Important: Only assemble and use the machine on a hori-
zontal surface. A non-horizontal surface can damage the
motor.
• If the machine tends to tilt or walk (especially when sand-
ing long and heavy panels), it must be fastened to a solid
surface of sufficient carrying force.
• Make sure the sanding belt runs in the correct direction. See
arrows at the back of the belt.
• Make sure the sanding belt is running correctly so that it can-
not come off the drive pulleys.
• Make sure the sanding belt is not twisted or loose.
• Firmly hold the workpiece when sanding.
• Always use the stop when using the sander in horizontal po-
sition.
• Always hold the workpiece firmly to the table when using
the disc sander.
• Always hold the workpiece to the side of the sanding disc
running downwards, in order to maintain the workpiece
pressed to the table. By using the upward-running side of
the sanding disc, the workpiece could be ejected and cause
injury to persons.
• Always keep a minimum distance of about 2 mm or less be-
tween the table or stop and the sanding belt or disc.
• Do not wear gloves. Do not hold the workpiece with a cloth
during sanding.
• Never sand workpieces too small to be held safely.
• Avoid awkward hand positions where a sudden slip could
cause your hand to touch the sanding belt or disc.
• When sanding a large piece of material, provide an addi-
tional support at table height.
• Never sand an unsupported workpiece. Secure the work-
piece with the table or the stop. Exceptions are the sanding
of curved workpieces on the outside of the sanding disc.
• Always clear the table, fence or sanding belt of scraps or
other objects, before turning the machine on.
• Do not perform any layout assembly or set-up work on the
table while the sander is in operation.
• Switch the machine off and pull the power plug from the sock-
et when fitting or removing accessories.
• Never leave the working area of the sander while the tool is
running, or as long as it has not come to an absolute stand-
still.
• Always place the workpiece on the sanding table or position
it firmly against the sanding stop. Place curved tools securely
on the table when sanding on the sanding disc.
• Always ensure that the belt and disc grinder are stable and
secured (e.g. fastened to a workbench).
• Before each use, check the grinding disc and grinding belt
for damage.
• Replace worn or damaged grinding discs and grinding belts
immediately.
• Always use the protective cover and the workpiece support
as required for the insert tools.
• Always use the electric tool with insert tools on both spindles
to limit the risk of contact with the rotating spindle.
Residual risks
The machine has been built according to the state-of-the-art
and the recognised technical safety requirements. However,
individual residual risks can arise during operation.
• Risk of injury for fingers and hands due to the rotating sand-
ing disc with improper guiding or positioning of the tool to
be sanded.
• Risk of injury from tools thrown away due to improper hold-
ing or guiding.
• Hazard due to electrical power with the use of improper
electrical connection cables.
• Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
• Residual risks can be minimised if the "safety instructions"
and the "intended use" are observed along with operating
manual in its entirety.
GB 17