Clarion CZ309E Benutzerhandbuch Seite 8

Radio Data System Operations
RDS (Radio Data System)
This unit has a built-in RDS decoder that sup-
ports broadcast stations transmitting "Radio
Data System" data.
When using the "Radio Data System" func-
tion, always set the radio to FM mode.
AF function
The AF function switches to a different fre-
quency on the same network in order to main-
tain optimum reception.
* The factory default setting is "ON".
1. Press the [ ] or [ ] button to select
"AF".
2. Press AF/TA button to select "AF ON" or "AF
OFF".
• AF ON:
"AF" in the display lights and the AF func-
tion turns on.
• AF OFF:
"AF" in the display goes off and the AF
function turns off .
REG (Regional Programme)
function
When the REG function is ON, the optimum
regional station can be received. When this
function is OFF, if the regional station area
switches as you drive, a regional station for
that region is received.
* The factory default setting is "ON".
Notes:
• This function is disabled when a national
station such as BBC R2 is being received.
• The REG function ON/OFF setting is valid
when the AF function is ON.
1. Press and hold PTY button to select "REG
ON".
Manually tuning a regional
station in the same network
1. This function is valid when the AF function
is ON and the REG function is OFF.
Note:
• This function can be used when a regional
broadcast of the same network is received.
12
TA (Traffi c Announcement)
In the TA standby mode, when a traffic an-
nouncement broadcast starts, the traffic an-
nouncement broadcast is received as top pri-
ority regardless of the selected function mode
so you can listen to it. Traffi c programme (TP)
automatic tuning is also possible.
* This function can only be used when "TP"
is lit in the display. When "TP" is lit, this
means that the RDS station being received
broadcasts traffic announcement pro-
grammes.
Setting the TA standby mode
If you press and hold the [AF/TA] button when
only "TP" is lit in the display, "TP" and "TA"
light in the display and the unit is set to the TA
standby mode until a traffic announcement
is broadcast. When a traffic announcement
broadcast starts, "TRA INFO" appears in the
display. If you press and hold the [AF/TA] but-
ton while a traffic announcement broadcast
is being received, the traffic announcement
broadcast reception is cancelled and the unit
goes into the TA standby mode.
Cancelling the TA standby mode
When "TP" and "TA" are lit in the display,
press and hold the [AF/TA] button. "TA" in the
display goes off and the TA standby mode is
cancelled.
* If "TP" is not lit, pressing and holding the [AF/
TA] button causes searching for a TP station.
Searching for a TP station
When "TP" is not lit, if you press and hold the
[AF/TA] button, "TA" lights in the display and
the unit automatically receives a TP station.
Auto store function for TP stations
You can automatically store up to 6 TP sta-
tions into preset memory. If the number of
TP stations that can be received is less than
6, the remaining broadcast stations already
stored in memory are left as are without being
overwritten.
When "TA" is lit in the display, press and hold
the [BAND] button (2 sec.). TP stations with a
suffi ciently strong signal are stored in the pre-
set memory.
Autogoods products «130»
Radio Data System Operations
* Even if you select FM1 or FM2, TP stations
are stored in the memory for FM3.
PTY (Programme Type)
This function enables you to listen to a broad-
cast of the selected programme type even
if another source mode than radio has been
selected.
* Some countries do not yet have PTY
broadcast.
* In the TA standby mode, a TP station has
priority over a PTY broadcast station.
* The factory default setting is "OFF".
Press the [PTY] button to select "ON" or
"OFF".
• ON:
"PTY" lights in the display and the PTY
standby mode is turned on. When the se-
lected PTY broadcast starts, the PTY item
name appears in the display.
• OFF:
"PTY" in the display goes off and the PTY
standby mode is cancelled.
Cancelling a PTY interrupt broadcast
Performing any tuning operation during a PTY
interrupt broadcast will cancel PTY reception
and return the unit to the PTY standby mode.
Selecting PTY
Press the PTY button, then use a number but-
ton [1] - [6] to select PTY type. The unit begins
searching after the programme type has been
selected.
TA volume setting
The volume for Traffi c Announcements can be
preset.
* Press the ADJ button repeatedly until
TAVOL appears in the display, then turn the
[VOL/SEL] knob to adjust the TA volume
level.
* When the TA interrupt ends, the volume
returns to the level that was set before the
interrupt.
13