Clarion CZ309E Benutzerhandbuch Seite 7

5. OPERATIONS
Basic Operations
Note:
• Be sure to read this chapter referring to the
chapter "3. CONTROLS"
CAUTION
When the unit is turned on, starting and
stopping the engine with the volume
raised to the maximum level may harm
your hearings.
Be careful when adjusting the volume.
Power on / off
Notes:
• Start the engine before using this unit.
• Be careful about using this unit for a long
time without running the engine. This could
completely drain the car battery, and you
may not be able to start the engine. Ad-
ditionally, this will reduce the service life of
the car battery.
1. Start the engine. The power button / knob
illumination on the unit will light up.
Engine ON
position
2. Press the [PWR] key on the front panel or
the [ ] key on the remote control to turn
on the power off standby mode. The unit
goes back to the last status after power on.
3. Press and hold the [PWR] key on the front
panel or press the [ ] key on the remote
control to turn off the power during opera-
tion.
CT (Clock Time) display
• The displayed clock data is based on the
CT (Clock Time) data in the RDS signal.
10
Mute
Press the [MUTE] key on the front panel or
remote control to mute the volume.
Note:
To restore the sound, repeat the operation
above again or adjust the volume manually.
Volume adjustment
Turn the volume knob on the front panel or
press the [VOL] key on the remote control.
The adjustable range of volume is 0 to 47.
CAUTION
While driving, keep the volume level at
which external sounds can be heard.
Source selection
Press the [SRC] key on the front panel or re-
mote control repeatedly to choose the desired
playing source.
Notes:
1. Source selection refers to selecting the op-
erating mode, such as DISC mode, Radio
mode, Aux mode, etc.
2. When some devices are not ready, they
cannot be selected.
Display system time
Press the [DISP] key on the front panel or re-
mote control to switch the display information
between system time and playing source.
Autogoods products «130»
Radio Operations
Select tuner as playing source
Press the [SRC] button once or more to enter
the radio mode.
Select a radio band
Press the [BAND] key on the panel or remote
control to select a radio band among FM1,
FM2, FM3, MW1 and MW2.
Manual tuning
During manual tuning, the frequency will be
changed in steps.
Press the [ ]/[ ] key on the panel
or remote control to tune in a higher / lower
station.
Auto tuning
Press and hold the [ ]/[ ] key on the
panel or remote control to seek a higher /
lower station.
To stop searching, repeat the operation above
or press any other key with a radio function.
Note:
When a station is received, searching stops
and the station is played.
If the unit receives a stereo broadcast, the
stereo 'ST' indicator light on the LCD display
lights.
Auto save
Only stations with suffi cient signal strength
will be detected and stored in the memory.
Press and hold the [BAND] key (2 sec.) to
start automatic station search.
To stop auto save, any other key with a radio
function.
Notes:
1. After auto save, the previously saved sta-
tions will be overwritten.
2. The unit has 5 bands: FM1, FM2, FM3,
AM1, AM2. Each band can store 6 stations;
hence the CZ309E can store 30 stations in
total.
3. During automatic station search, the de-
tected 6 stations will be stored only on the
FM3 band.
Manual save
When one expected radio station has been
detected, press and hold number key 1~6 to
save it in the memory.
Recall the stored stations
Press a numeric key from 1 to 6 on the
panel or on the remote control to select the
corresponding stored station.
Local seek
When LOCAL seek is on, only radio stations
with a strong radio signal can be received.
To switch the LOCAL function on/off , press
the [ADJ] key on the front panel, then press
[ADJ] repeatedly until LOCAL or DX id
displayed, and turn the knob to select Local or
Distant mode.
Notes:
The number of radio stations that can be
received will decrease when Local seek mode
is on.
11