Kärcher CNS 18-30 Battery Bedienungsanleitung Seite 21

front handle. Holding the chain saw with a reversed
hand configuration increases the risk of personal in-
jury and should never be done.
● Hold the chain saw by insulated gripping surfac-
es only, because the saw chain may contact hid-
den wiring. Saw chains contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
● Wear eye protection. Further protective equip-
ment for hearing, head, hands, legs and feet is
recommended. Adequate protective equipment will
reduce personal injury from flying debris or acciden-
tal contact with the saw chain.
● Do not operate a chain saw in a tree, on a ladder,
from a rooftop, or any unstable support. Opera-
tion of a chain saw in this manner could result in se-
rious personal injury.
● Always keep proper footing and operate the
chain saw only when standing on fixed, secure
and level surface. Slippery or unstable surfaces
may cause a loss of balance or control of the chain
saw.
● When cutting a limb that is under tension, be
alert for spring back. When the tension in the
wood fibres is released, the spring loaded limb may
strike the operator and/or throw the chain saw out of
control.
● Use extreme caution when cutting brush and
saplings. The slender material may catch the saw
chain and be whipped toward you or pull you off bal-
ance.
● Carry the chain saw by the front handle with the
chain saw switched off and away from your
body. When transporting or storing the chain
saw always fit the guide bar cover. Proper han-
dling of the chain saw will reduce the likelihood of
accidental contact with the moving saw chain.
● Follow instructions for lubricating, chain ten-
sioning and changing the bar and chain. Improp-
erly tensioned or lubricated chain may either break
or increase the chance for kickback.
● Cut wood only. Do not use chain saw for purpos-
es not intended. For example: do not use chain
saw for cutting metal, plastic, masonry or non-
wood building materials. Use of the chain saw for
operations different than intended could result in a
hazardous situation.
● Do not attempt to fell a tree until you have an un-
derstanding of the risks and how to avoid them.
Serious injury could occur to the operator or by-
standers while felling a tree.
● Follow all instructions when clearing jammed
material, storing or servicing the chain saw.
Make sure the switch is off and the battery pack
is removed. Unexpected actuation of the chain saw
while clearing jammed material or servicing may re-
sult in serious personal injury.
Causes and operator prevention of kickback
Kickback may occur when the nose or tip of the guide
rail touches an object, or when the wood closes in and
pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse
reaction, kicking the guide rail up and back towards the
operator.
Pinching the saw chain along the top of the guide rail
may push the guide rail rapidly back towards the opera-
tor.
Either of these reactions may cause you to lose control
of the saw which could result in serious personal injury.
Do not rely exclusively upon the safety devices built into
your saw. As a chain saw user, you should take several
steps to keep your cutting jobs free from accident or in-
jury.
Kickback is the result of tool misuse and/or incorrect op-
erating procedures or conditions and can be avoided by
taking proper precautions as given below:
● Maintain a firm grip, with thumbs and fingers en-
circling the chain saw handles, with both hands
on the saw and position your body and arm to al-
low you to resist kickback forces. Kickback forc-
es can be controlled by the operator, if proper
precautions are taken. Do not let go of the chain
saw.
● Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact
and enables better control of the chain saw in unex-
pected situations.
● Only use replacement bars and chains specified
by the manufacturer. Incorrect replacement bars
and chains may cause chain breakage and/or kick-
back.
● Follow the manufacturer's sharpening and
maintenance instructions for the saw chain. De-
creasing the depth gauge height can lead to in-
creased kickback.
Additional General Safety Instructions
Note
● Regulations may restrict the use of this device
in some regions. Seek advice from your local authori-
ties.
DANGER
result of uncontrolled device movements. Keep body
parts away from moving parts. ● Risk of injury from
hurled or falling objects. Never use the device if there
are persons, in particular children or animals, within a
radius of 15 m. ● No changes may be made to the de-
vice.
WARNING
with these instructions are not allowed to operate the
device. The age of the operator may be limited by local
restrictions. ● You need an unobstructed view of the
work area in order to be able to recognise any potential
dangers. Use the device only under good lighting condi-
tions. ● Before operation, make sure that the device, all
control elements including the chain brake and safety
devices are working properly. Check for loose locks, en-
sure that all protective devices and handles are correct-
ly fitted and securely fastened. Only use the device
when it is in a correct condition. ● Never use the device
if the trigger on the handle does not switch on and off
correctly. ● Replace any worn or damaged parts before
operating the device. ● Risk of kickback due to loss of
balance. Avoid an abnormal posture, keep a stable,
safe footing and maintain your balance. ● Immediately
stop the device and check for damage or identify the
cause of the vibration if the device has been dropped,
hit or vibrates abnormally. Have damage repaired by the
authorised Customer Service or replace the device.
CAUTION
ing protection, strong and sturdy gloves and head pro-
tection when operating the device. Wear a face mask
when the work is dusty. ● Wear long, heavy trousers,
sturdy shoes and well-fitting gloves when working with
English
● Risk of fatal injury from cuts as a
● Children and persons unfamiliar
● Wear full eye protection and hear-
21