Z Optical Interface; Z Reduced Mains Power; Z Default Language; Z Door Opening At Programme End - Schulthess Fust NOVAMATIC WA 7097 Bedienungsanleitung

Optical interface (ex factory OFF)
Select «Extended basic settings»!
If the optical interface (SCS) is switched on, customer
services can communicate with the machine by PC.
Reduced mains power (ex factory OFF)
Select «Extended basic settings»!
If the connected load is reduced, the programme times
will be extended accordingly.
Off = 400 V 2N ~ 4,2 kW / 10 AT
On = 230 V 1N ~ 4,2 kW / 16 AT
On = 230 V 1N ~ 2,3 kW / 10 AT
Default language (ex factory GERMAN)
Select «Extended basic settings»!
If another language is temporarily selected via the
buttons «Top5» and «Quick wash», 4 minutes after
programme end, in stand by mode or after a long stand-
still, the setting reverts back to the default language.
Door opening at programme end (ex factory OFF)
Select «Extended basic settings»!
If this function is switched on, the door will open auto-
matically at the end of the programme.
Delete Top5
Select «Extended basic settings»!
When calling this function, it is always set to «OFF».
To delete the favourite programmes saved in «Top5»,
this function must be set to «ON» and the basic setting
must be quit using the quick wash button. This will
delete the programmes saved in «Top5», the basic set-
ting is set to «OFF» again and the memory «Top5» can
be filled with new favourite programmes.
Start time preselect (ex factory 24 HOURS)
Select «Extended basic settings»!
The maximum adjustable range of the start time delay
can be reset from 24 hours to 100 hours.
Information for testing institutes and users
Energy labelling according to Directive 2010/30/EU and
EN 60456 is based on the «ecoPlus» programmes for
coloureds at 60°C, full and half loads, and coloureds at
40°C, half loads.
Annual energy consumption: 175 kWh
Annual water consumption:
46
9300 litres

Cleaning and Maintenance

Cleaning the machine

Ensure that the power supply is switched off before any
cleaning, care or maintenance work.
Under no circumstances spray the machine with water
or clean it with a steam cleaner.
Do not use solvents! These substances can damage
parts of the machine, produce poisonous vapour and
carry the risk of explosion.
Casings and control areas should only be cleaned with
soap or a commercially available, solvent-free, non-abra-
sive cleaning product.
The side walls of machines with a chrome steel finish
should not be cleaned with chrome steel cleaner under
any circumstances.
Descaling the machine
If the correct amounts of detergent are used, descaling
is no longer necessary in general.
Descalers contain acids, can attack parts of the machine
and cause discolouration of laundry.
If you do, however, wish to descale the machine, follow
the manufacturer›s instructions on the packet.
Limescale formation depends largely on the hardness of
the water. To avoid water damage, we recommend
having this checked by a specialist after around 5 years
of fault-free operation.
Cleaning the drum
Rust marks caused by metal parts standing still for
lengthy periods can be removed with a chlorine-free
cleaning product (look at the description of the ingre-
dients on the pack).
Never use steel wool!
Water supply hose
Only for machines without water stop. To avoid water
damage, we recommend having this checked by a
specia list after around 5 years of fault-free operation.
Frost protection
If the machine is in a room susceptible to frost, all residual
water must be removed from the detergent pump and
water supply and drain hoses immediately after use.
Emptying the drain pump
See chapter «Emergency emptying».
Emptying the water supply hose
 Turn off the water supply
On machines without Water Stop
 Screw off the hose at the tap, let the water run into a
bowl.
 Screw the hose back onto the tap.