Machine Operation - Schulthess Fust NOVAMATIC WA 7097 Bedienungsanleitung

«FOAM, PROG. CANCEL»
X Due to extremely intensive foaming, the washing
machine could not complete the spinning cycle and the
wash programme had to be aborted.
X Repeat the wash programme without adding any
detergent.
X In future, please reduce the detergent quantity (if
re quired use washing powder instead of liquid detergent).
«WATER LEVEL TOO HIGH»
 Too much foam in the washing machine, spinning has
not been effected. There are two possibilities to solve
the problem:
a) Press the Start button and then interrupt the pro-
gramme by pressing the Quick Wash button several times
until the display «OPEN DOOR» appears.
Mix approx. 30 ml conditioner and approx. 1 litre water.
Start the previously selected wash programme (it may
take several minutes until the machine is released for
the selection of a new programme). After the water
s upply has been com pleted, switch forward immediately
to «Conditio ning» by pressing the Quick Wash button
and add the conditioner- water mixture into section I of
the detergent drawer. The programme should now end
as usually and the spinning process should take place.
Afterwards repeat the desired programme, however
with out any detergent.
or
b) Press the Start button and then interrupt the pro-
gram me by pressing the Quick Wash button several
times until the display «OPEN DOOR» appears. Wait for
approx. 1 hour and start the previously selected wash
programme, move forward immediately to «spinning»
using the Quick Wash button. Usually the laundry will
be spun. If not, repeat the procedure including waiting
for 1 hour. After wards repeat the desired programme,
however without any detergent.
X The maximum admissible water level is reached. Wait
until the water has been pumped out completely and
press the Start button. The programme will continue.
«WATER IS BEING PUMPED OUT»
 Too much water is in the washing machine. Water is
pumped off to the set level.
 If you see a lot of foam in the door glass, this means
that too much foam is in the washing machine.
To eliminate this problem proceed as for the error mes-
sage «WATER LEVEL TOO HIGH».
 In future, please reduce the detergent quantity.
If the appliance shows a function fault F – –:
X Stop the programme with the Quick Wash button
and select a new programme.
In the event of repeated error messages:
X Disconnect the electricity for approx. 1 minute and
then switch on again. (Withdraw the mains plug or
switch off the main building switch.)
X The machine is ready to operate once again when the
programme pilot lamps flash.
X Select a new programme.
If the error message still appears:
X Make a note of the error message
X Switch off the water tap and withdraw the mains
plug or switch off the main building switch.
X Inform Customer Service.
50
Troubleshooting
Other minor faults, which you can rectify yourself.

Machine operation

Display is dark:
X The machine is in standby mode. No error. To operate
the machine press any key.
The machine cannot be switched on, display
remains dark even after pressing a key:
X Check whether the mains power is switched on at the
wall and the plug is in.
X Check whether all the fuses are intact or the safety
switch has tripped.
X Mains blockage, generally at noon. Operate the
machine after the mains blockage has ended.
The machine does not start:
X The Start button has not been pressed.
X Start time preselect has been set. Only starts at the
preselected start time.
Loading door cannot be opened:
X Programme not yet finished.
X «Rinsing stop» selected. No error; see chapter
«Washing/Ending the programme with rinsing stop».
X Mains blockage or appliance defect: see below.
Open the door in the event of a power failure
or machine defect as follows:
X Check that the drum is standing still.
X Turn off the water tap
X Switch off the mains power supply.
X Carry out emergency emptying (see chapter
«Cleaning and Maintenance»).
X Pull on the door opener (emergency open
X The door will open.
Drum lighting does not work:
(Option)
X The electric light bulb is defective. For safety reasons
the lamp must only be replaced by the customer service
or a qualified specialist.
ing).