Kohler DIESEL 4000 E XL C5 Benutzer- Und Wartungshandbuch Seite 19

2.7.4 Connection and choice of cables
For all connections, use flexible, strong rubber-sheathed cables which comply with standard IEC 60245-4 or equivalent cables, and
ensure that these are kept in perfect condition. Only use one item of class I electrical equipment per socket and connect up
equipment using a cable equipped with a PE protective conductor (green/yellow); this protective conductor is not required for
class II equipment. Adhere to the cross sections and lengths recommended in this table during installation or when using electrical
extensions.
Equipment type:
Type of unit connector:
Recommended cable cross section:
0 to 50 m
Length of
51 to 100 m
cable used
101 to 150 m*
*This cable length is the maximum permitted length, and must not be exceeded.
Installation method = cables on raceway or non-drilled tablet/Permitted drop in voltage = 5%/Multi-core conductors/Cable type PVC 70°C (e.g.
H07RNF)/Ambient temperature =30°C.
2.8 Risk of hearing loss
DANGER
2.9 Risks during handling operations, use and maintenance
For safety reasons, all operations must be carried out by staff with the necessary skills and using suitable
equipment. Maintenance must be carried out on a regular and conscientious basis, using only original parts. Gloves
must be worn.
Safety guidelines for handling petroleum products:
DANGER
Safety guidelines for handling batteries:
DANGER
3.1 Key to illustrations
The cover illustrations can be used to identify the various components of the unit. The procedures in the manual refer to these
illustrations using letters and numbers as identifiers: "A1" refers to the number 1 on figure A.
Earth terminal
Battery
Dipstick A3-B1
Dipstick upper limit
Dipstick lower limit
Oil filler cap
Fuel level indicator
Fuel tank cap
Fuel tap
Key
The unit may be equipped with the "GS101-Generator Smart Care" option (A19): the Bluetooth GSC101 box
transmits all the information needed to monitor the unit to an application to be installed on your mobile phone; this
includes maintenance dates, a maintenance aid, and the map of approved resellers for any spare parts required.
1084_EN.docx
10 A
mm² AWG
4 10
10
10
RISK OF HEARING LOSS
Suitable hearing protection must be worn at all times when the unit is running.
RISK OF POISONING OR EXPLOSION
Respect the local regulations in force concerning the handling of petroleum products. Fill up when the
unit is switched off and the engine cold. Smoking, using a naked flame, producing sparks and making
telephone calls are forbidden when filling the tank. After filling, always check that the tank's filler cap is
properly tightened. Clean any traces of fuel with a clean cloth and wait until the vapors have dispersed
before starting the unit. If the fuel is exposed to high temperatures for a period of several hours
(containers or generating set stored in a vehicle parked in the sun, for example), harmful vapors could
be released causing a risk of poisoning or of feeling unwell.
The fluids used by the units, such as oils and fuels, are dangerous products. Never inhale or ingest;
avoid prolonged or repeated contact with the skin.
RISK OF POISONING OR EXPLOSION
Follow the battery manufacturer's recommendations. Only use insulated tools. Keep away from fire or
naked flames. Always ensure adequate ventilation during charging.
A1 Solenoid valve
A2 Starter-recoil reel
Electrical sockets
B2 Stop lever
B3 Oil drain plug
A4 Oil filter
A5 Oil filter screw
A6 Fuel filter
A7 Fuel filter mounting clip
A8 Fuel filter mounting clip screw
Single-phase
16 A
mm² AWG mm²
6 9 10
7 10 7 25
7 16 5 35
Section 3. Getting started with the generating set
A9 Air filter
A10 Wheel
A11 Air filter cover
A12 Wing nut
A13-B4 Paper element
A14-B6 Rubber seal
B5 Exhaust silencer
A15-C1 Circuit breakers
C2 GSC101-Generator Smart Care
C3
15/250
Three-phase
32 A 10 A
AWG mm² AWG
7 1.5 14
3 2.5 12
2 4 10
16 A
mm² AWG
2.5 12
4 10
6 9
A16
D1
D2
D3
D4
D5
A17
A18
A19
2020-08-14