Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
The supplied mortar beater is suited for following materials:
larger amounts of tenacious and glutinous compounds to
-
be mixed such as paints, varnish, translucent inks, ad-
hesives, paste, glue, knifing filler, plaster, flooring plaster
etc.
Always use this device with the extra handles fitted.
Increase the speed during the mixing process. Immerse the
beater through the material to be mixed until it is thoroughly
mixed. Follow the processing instructions from the suppli-
ers.
Do not work with low speed in continuous mode.
This may result in overloading/overheating the motor as
no sufficient cooling can be generated.
Hold the device with both hands during mixing.
Do not reach in the running beater (rotating beat-
er).
Avoid splashing. Work with low speed when immersing
the beater in the material to be mixed or pulling it out.
M
a
i
n
t
e
n
M
a
i
n
t
e
n
Before each maintenance and cleaning work:
- switch off device
- wait for standstill of the beater
- pull out power plug
Use only original parts. Other parts can result in unexpected
damages and injuries.
Maintenance and repair work beyond this is only allowed to be
carried out by the manufacturer or authorized service staff.
Store unused equipment in a dry, locked place out of the reach
of children.
Before each fault elimination:
− switch off device
− wait for standstill of the beater
− pull out power plug
After each fault clearance, put into operation and recheck all security installations.
Problem
Motor does not start.
Unusual vibrations
a
n
c
e
a
n
d
C
a
r
e
a
n
c
e
a
n
d
C
a
r
e
Possible cause
⇒ No power supply (power failure)
⇒ Mains cable defective.
⇒ Motor or switch defect
⇒ Beater defective.
⇒ Chuck defective.
⇒ Non-intended material to be mixed.
Observe the following to maintain the operability of the
machine:
Keep vent slits clean and free from obstructions.
Remove dust and dirt using a cloth or a soft brush.
Do not clean the machine with running water or high-
pressure cleaners.
Do not use solvents for the synthetic parts (petrol, alcohol,
etc.) as these can damage the synthetic parts.
Check that the handles are properly secured.
Clean the beater.
The agitator is equipped with carbon brushes. Have the
carbon brushes be replaced by the customer service if they
are worn
Regularly check the beater for damages for your own
safety. Immediately replace any damaged beater.
Check the shaft on a regular basis. An agitator with
defective shaft must no longer be used. Have the device be
repaired by the customer service.
Store unused equipment in a dry, locked place out of the
reach of children.
Before a longer period of storage carry out the following to
extend the machine's service life and ensure an easy operat-
ing:
− thoroughly clean the device
Please observe the enclosed terms of guarantee.
P
o
s
s
i
b
l
e
f
a
u
l
t
s
P
o
s
s
i
b
l
e
f
a
u
l
t
s
Remedy
⇒ Check fuses (10 A)
⇒ Exchange defect cable, respectively check extension
cable, (by electrician)
Never use defect lead
⇒ To correct the problem, refer to the manufacturer or
other approved service centre.
⇒ Replace the beater.
⇒ To correct the problem, refer to the manufacturer or
other approved service centre.
⇒ Incorrect processing. Follow the processing instructions
from the supplier.
S
t
o
r
a
g
e
S
t
o
r
a
g
e
Pull out power plug
G
u
a
r
a
n
t
e
e
G
u
a
r
a
n
t
e
e
14
Werbung
Inhaltsverzeichnis
