Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
more safety warnings - „Service"
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer ser-
vice points.
Use only original spare parts. Accidents can arise for
the user through the use of other spare parts. The
manufacturer is not liable for any damage or injury re-
sulting from such action.
A
D
e
s
c
r
i
p
t
i
o
n
o
A
D
e
s
c
r
i
p
t
i
o
n
o
Pos Denomination
1.
Agitator
2.
Mortar beater
a) Bar
b) Beater attachment
3.
ON / OFF-switch
4.
Trip switch
5.
Speed control
6.
2-speed switch
7.
Handle
8.
Shaft
9.
Spanners
10.
Spiral beater
11.
Disk beater
A
A
Chucking the beater:
B
Screw the bar (2a) on the beater attachment (2b).
C
Screw the beater assembly (2) on the shaft (8). Secure the
beater using the spanners (9).
S
S
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Check that the machine is completely and correctly assem-
bled.
Before each use, check
Connection cables for defects (cracks, cuts, etc.).
−
Do not use any defective cables.
there are no damages at the machine
−
(see "safe working")
that the beater is properly secured.
−
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to
the relevant and properly earthed plug.
13
f
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
f
d
e
v
i
c
e
/
S
p
a
r
e
p
a
r
Order-No.
RW 1400
RW 1600 A
372582
372612
Ø120
Ø140
372562
372583
372613
Ø120
372614
Ø114
s
s
e
m
b
l
y
s
s
e
m
b
l
y
t
a
r
t
-
u
p
t
a
r
t
-
u
p
Connect the machine via a 30 mA fault current safety
switch.
Do not use any defective connection cables.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm².
In case of disadvantageous power system conditions short-
term voltage reductions can occur during the starting pro-
cess of the device which can influence other devices (e.g.
jittering of a lamp). No failures are expected when the house
service connection has a continuous currect-carrying capac-
ity greater than 100 A per phase.
t
s
t
s
Main fuse: 10 A
Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
or replaced immediately by the customer service.
Switching on
Operate the trip switch (4) at first. Press the ON/OFF button (3)
on the handle.
Start the machine at the lowest rotational speed. Increase
the rotational speed with the speed control dial (5) if required.
Ø140
Switching off
Release the ON/OFF handle button.
The device is equipped with a 2-speed gear.
1. speed: 0 min
2. speed: 0 min
For the speed selection turn the switch (6) by 180°.
Only operate this switch at standstill.
With this type, the motor's speed and thus the agitator perfor-
mance can be adjusted. You can continuously adjust the speed
with the speed control (5).
•
Level 1 Min. power = SLOW.
•
Level 6 max. power = FAST.
In any case, adhere to all safety notes (see "Safe
working").
Only use beaters recommended by the manufacturer.
Pay attention the max. diameter (Ø 120 mm - RW
1400 / Ø 140 mm - RW 1600 A).
Switching on/off
D
F
2- speed gear
RW 1400
- 700 min
0 min
-1
-1
- 940 min
0 min
-1
-1
E
Speed control
W
o
r
k
i
n
g
w
i
t
h
t
h
e
a
g
W
o
r
k
i
n
g
w
i
t
h
t
h
e
a
Instruction for using the agitator
RW 1600 A
- 420 min
-1
-1
- 760 min
-1
-1
i
t
a
t
o
r
g
i
t
a
t
o
r
Werbung
Inhaltsverzeichnis
