Hydraulic Circuit - Sulky Xeos TF Originalbetriebsanleitung

DRIVE EQUIPMENT
(Power take-off and universal drive shafts)
1 - Only use universal drive shafts supplied with the
machine or recommended by the manufacturer.
2 - Power take-off and universal drive shaft guards
must always be fitted and in good condition.
3 - Ensure that the tubes of the universal drive shafts
are properly guarded, both in the working position
and in the transport position.
4 - Before connecting or disconnecting a universal
drive shaft, disengage the power take-off, turn off
the engine and re-move the key from the ignition.
5 - If the primary universal drive shaft is fitted with a
torque limiter or a free wheel, these must be moun-
ted on the machine power take-off.
6 - Always ensure that universal drive shafts are fit-
ted and locked correctly.
7 - Always ensure that universal drive shaft guards
are immobilized in rotation using the specially provi-
ded chains.
8 - Before engaging power take-off, ensure that the
speed selected and the direction of rotation of the
power take-off comply with the manufacturer's ins-
tructions.
9 - Before engaging power take-off, ensure that no
persons or animals are close to the machine.
10 - Disengage power take-off when the universal
drive shaft angle limits laid down by the manufactu-
rer are in danger of being exceeded.
11 - Caution! When power take-off has been disen-
gaged, moving parts may continue to rotate for a
few moments. Do not approach until they have rea-
ched a complete standstill.
12 - On removal from the machine, rest the universal
drive shafts on the specially provided supports.
13 - After disconnecting the universal drive shafts
from the power take-off, the protective cap should
be fitted to the power take-off.
14 - Damaged power take-off and universal drive
shaft guards must be replaced immediately.
DANGER
1
Rotating shaft
Agitator in the hopper
Universal drive joint
2
Rotating turbine
3
The triangular hitch represents a
crushing hazard
4
Do not remain on the walkway
5
Moving parts
6

HYDRAULIC CIRCUIT

1 - Caution! The hydraulic circuit is pressurized.
2 - When fitting hydraulic motors or cylinders, ensure
that the circuits are connected correctly in accor-
dance with the manufacturer's guidelines.
3 - Before fitting a hose to the tractor's hydraulic cir-
cuit, ensure that the tractor-side and machine-side
circuits are not pressurized.
4 - The user of the machine is strongly recommended
to identify the hydraulic couplings between the trac-
tor and the machine in order to avoid wrong connec-
tion. Caution! There is a danger of reversing the
functions (for example: raise/lower).
5 - Check hydraulic hoses once a year:
. Damage to the outer surface
. Porosity of the outer surface
. Deformation with and without pressure
. State of the fittings and seals
The maximum working life for hoses is 6 years. When
replacing them, ensure that only hoses with the spe-
cifications and grade recommended by the machine
manufacturer are used.
6 - When a leak is found, all necessary precautions
should be taken to avoid accidents.
7 - Pressurized liquid, particularly hydraulic circuit
oil, may cause serious injury if it comes into contact
with the skin. If the case of injury, consult a doctor
immediately. There is a risk of infection.
8 - Before any operation on the hydraulic circuit,
lower the machine, release the pressure from the cir-
cuit, turn off the engine and remove the key from the
ignition.
MAINTENANCE
1 - Before commencing any maintenance, servicing
or repair work, or before attempting to locate the
source of a breakdown or fault, it is essential that the
power take-off is disengaged, the engine turned off
and the key removed from the ignition.
2 - Check regularly that nuts and screws are not
loose. Tighten if necessary.
1
4
5
3 - Before carrying out maintenance work on a rai-
sed machine, prop it up using appropriate means of
support.
4 - When replacing a working part (fertilizer sprea-
der blade or seed drill coulter), wear protective
gloves and only use appropriate tools.
5 - To protect the environment, it is forbidden to
throw away oil, grease or filters of any kind. Give
them to specialist recycling firms.
6 - Before operating on the electric circuit, discon-
nect the power source.
7 - Protective devices likely to be exposed to wear
and tear should be checked regularly. Replace them
immediately if they are damaged.
8 - Spare parts should comply with the standards
and specifications laid down by the manufacturer.
Only use the manufacturer's spare parts.
9 - Before commencing any electric welding work on
the tractor or the towed machine, disconnect the al-
ternator and battery cables.
10 - Repairs affecting parts under stress or pressure
(springs, pressure accumulators, etc.) should be car-
ried out by suitably qualified engineers with special
tools.
3
2
EN