Herunterladen Inhalt Inhalt Diese Seite drucken

Date And Time; Correcting Image Properties - Monacor DMR-180 SET Bedienungsanleitung

Digitaler multiplexrekorder
Vorschau ausblenden Andere Handbücher für DMR-180 SET:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
GB
3) In the column
TITLE
, click the first character to be
changed in the line of the camera channel to be
set. A set of characters with upper-case letters
will appear (fig. 15).
Set of characters with upper-case letters
Set of characters with lower-case letters
Set of characters with numbers
Click the letter desired. Now enter the next letter.
To change to the lower-case letters (fig. 16),
click
ABC
and to change to the numbers (fig. 17),
click
abc
. If you click 123, you will return to the
upper-case letters. To delete the last character
entered, click the icon ←. To terminate the input,
click the icon ↵.
For operation without mouse, first select the
input field with the buttons
and
(13) on the recorder or
on the remote control and confirm with the button
SEL / EDIT (9) or SEL (33). The first character will
be highlighted now. Select the character position
to be changed with the buttons
(13) or
and
(29) and confirm with SEL / EDIT
(9) or SEL (33). Now the set of characters with
upper-case letters will appear. To enter and
delete a character and to change the sets of char-
acters, as described for mouse operation, use the
buttons
,
(8),
(10),
(29) and then confirm with SEL / EDIT (9) or
SEL (33). After completing the input via the icon
↵, exit the input field by pressing the button
MENU / ESC (7) or MENU (32).
Enter the names of the other camera channels
in the same way.
4) In the column
POSITION
ding list field if and where the name is to be
inserted in the image:
UPLEFT
insertion at the top on the left
DOWNLEFT
insertion at the bottom on the left
UPRIGHT
insertion at the top on the right
DOWNRIGHT
insertion at the bottom on the right
OFF
5) For DMR-188 only:
For setting the camera channels 5 – 8, click
PREV.
Then click
to return to the previous menu
page.
6) To reset all settings of this submenu to the factory
settings, click the button
7) To store the settings, click the button
confirm the message inserted "
fully!
" by clicking the button
8) To exit the submenu, click the button
right mouse button or press the button MENU /
ESC (7) or MENU (32).
26
6.2.4
The recorder is equipped with a clock. Due to a bat-
tery, this clock will still run when the recorder is
switched off or in case of power failure. To set the

date and time:

1) Activate the
2) Activate the submenu
(fig. 11).
3) Activate the submenu
(fig. 18).
Submenu TIME SETUP
4) In the list field next to
desired format for indicating the date:
and
(8),
(10)
MM / DD / YY
,
,
,
(29)
next to
name (
(10) and
5) In the list field next to
hour or 12-hour indication. Then enter the current
time in the input field next to
format has been selected, define
additional list field.
6) In the list field next to
(13) or
,
,
,
zone of the place of application (e. g.
7) In the list field next to
change for daylight saving time (
next to
the usual times (
, define in the correspon-
individually (
field next to
saving time is to be made in the first, second, third
or fourth week and next to
the change to daylight saving time is to be made
on a Sunday at 2 a. m. In the line below it, define
the date for the change back to standard time.
8) To reset all settings of this submenu to the factory
settings, click the button
NEXT
.
9) To store the settings, click the button
confirm the message inserted "
fully!
DEFAULT
.
10)To exit the submenu, click the button
right mouse button or press the button MENU /
APPLY
, then
ESC (7) or MENU (32).
Saved success-
OK
.
If the clock does not keep the current time until the
EXIT
or the
recorder is switched on again, the battery (button
cell inside the recorder) may be exhausted und must
be replaced.
Date and time
MAIN MENU
(fig. 10).
SYSTEM
/
SYSTEM SETUP
DATE/TIME
/ TIME
DATE FORMAT
or
YY-MM-DD
Then enter the current date in the input field
DATE
. It will be entered like the camera
chapter 6.2.3).
TIME FORMAT
TIME
. If the 12-hour
AM
TIME ZONE
, select the time
DST
, select automatic
ON
) or not (
If
ON
has been selected, define in the list field
DST MODE
if the change is to be effected at
DEFAULT
) or at a time defined
CUSTOM
).
If
CUSTOM
has been selected, define in the list
STARTTIME
if the change to daylight
SUNDAY
in which month
DEFAULT
.
Saved success-
" by clicking the button
OK
.
6.2.5

Correcting image properties

The properties of the camera images may be cor-
rected, if required. For this purpose, in the submenu
CAMERA/ DISPLAY SETUP
line for the camera channel to be set and select it
with the buttons
(13) on the recorder or
remote control and confirm with the button SEL /
EDIT (9) or SEL (33).
SETUP
The submenu for setting the image properties
SETUP
(fig. 19) will appear:
For DMR-188 only:
For setting the camera channels 5 – 8, click
first. Then click
PREV.
page.
Submenu COLOR SETUP
To set the values for
, select the
SATURATION
, move the sliding controls shown on
the menu. If no mouse is connected, select the cor-
responding control with the buttons
and change the value with the buttons
(13) or
,
(29).
To reset all settings of this submenu to the factory
settings, click the button
, select 24-
To store the settings, click the button
confirm the message inserted "
fully!
" by clicking the button
or
PM
in the
To exit the submenu, click the button
right mouse button or press the button MENU / ESC
(7) or MENU (32).
GMT
for UK).
OFF
).
APPLY
, then
EXIT
or the
(fig. 14), click
SETUP
in the
and
(8) and
(10) and
,
,
,
(29) on the
COLOR
NEXT
to return to the previous menu
HUE
BRIGHT
CONTRAST
,
,
and
and
(8, 29)
(10) and
DEFAULT
.
APPLY
, then
Saved success-
OK
.
EXIT
or the

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dmr-188Dmr-184

Inhaltsverzeichnis