Bender RCMB104 Handbuch Seite 18

RCMB104
Ein-/Ausgänge
Anschlussart ..................... Leiterplattensteckverbinder 0,5 x 0,5 mm
Anordnung der Anschlüsse ............................... zweireihig 2 x 4 Pins
Rastermaß ...........................................................................2,00 mm
Kontaktoberfläche ................................................................verzinnt
Stiftlänge ................................................................................2,5 mm
Lötverfahren für PCB ............................ Empfehlung: selektives Löten
Anschluss Messstromwandler CTBC17
Maximaler Abstand zu Steckverbinder ..................................100 mm
Anschlussart ...........................................Leiterplattensteckverbinder
Anzahl der Pole ............................................................. 6 (2x3-polig)
Rastermaß .............................................................................3,0 mm
Anzahl der Steckzyklen ..................................................................30
Hersteller Typenbezeichnung ................... Molex MicroFit 3.0 Header
Artikelnummer ................................................................43045-0607
Der Steckverbinder ist nicht Bestandteil des Lieferumfangs. Weitere
Informationen sind dem von Molex erstellten Original-Datenblatt zu
entnehmen.
Normen und Zulassungen
Die Überwachungsmodule entsprechen, je nach
Variante, den folgenden Gerätenormen:
RCMB104-1 und -3M:
IEC 62752 Ladeleitungsintegrierte Steuer- und
Schutzeinrichtungen für die Ladebetriebsart 2 von
Elektro-Straßenfahrzeugen (IC-CPD)
RCMB104-2:
CCID20 nach UL 2231-2 (Personnel Protection
Systems for Electric Vehicle (EV) Supply Circuits:
Particular Requirements for Protection Devices for
Use in Charging Systems)
RCMB104-2
CCID5 nach UL 2231-2 (Personnel Protection Systems
for Electric Vehicle (EV) Supply Circuits: Particular
Requirements for Protection Devices for Use in
Charging Systems)
18 RCMB104_D00294_04_M_DEEN / 02.2023
Inputs/outputs
Connection type ........................PCB plug-in connector 0.5 x 0.5 mm
Arrangement of connections ............................double row 2 x 4 pins
Modular dimensions ............................................................2.00 mm
Contact surface ........................................................................tinned
Pin length ...............................................................................2.5 mm
Soldering process for PCB..............recommended: selective soldering
Connection measuring current transformer
CTBC17
Maximum distance to connector ..........................................100 mm
Connection type ..............................................PCB plug-in connector
Number of poles ............................................................ 6 (2x3 poles)
Modular dimensions ..............................................................3.0 mm
Number of mating cycles ...............................................................30
Manufacturer type designation ................ Molex MicroFit 3.0 Header
Article number ................................................................43045-0607
The connector is not included in the scope of delivery. For further in-
formation, refer to the original data sheet created by Molex.
Standards and approvals
The monitoring modules compliens, depending on
the variant, with the following device standards:
RCMB104-1 and -3M:
IEC 62752 In-cable control and protection device for
mode 2 charging of electric road vehicles (IC-CPD)
RCMB104-2:
CCID20 acc. to UL 2231-2 (Personnel Protection
Systems for Electric Vehicle (EV) Supply Circuits:
Particular Requirements for Protection Devices for
Use in Charging Systems)
RCMB104-2
CCID5 acc. to UL 2231-2 (Personnel Protection
Systems for Electric Vehicle (EV) Supply Circuits:
Particular Requirements for Protection Devices for
Use in Charging Systems)
außer / eccept
RCMB104-1 und -3M