Olimpia splendid SHERPA MONOBLOC S2 E 6 Installationsanleitung Seite 117

FOR SERVICEMAN
1 DHW MODE SETTING
2 COOL MODE SETTING
3 HEAT MODE SETTING
4 AUTO MODE SETTING
5 TEMP. TYPE SETTING
6 ROOM THERMOSTAT
7 OTHER HEATING SOURECE
8 HOLIDAY AWAY SETTING
9 SERVICE CALL
10 RESTORE FACTORY SETTINGS
11TEST RUN
12 SPECIAL FUNCTION
13 AUTO RESTART
14 POWER INPUT LIMITATION
15 INPUT DEFINE
16 CASCADE SET
17 HMI ADDRESS SET
18 COMMON SET
1 DHW MODE SETTING
1.1 DHW MODE
1.2 DISINFECT
1.3 DHW PRIORITY
1.4 PUMP_D
1.5 DHW PRIORITY TIME SET
1.6 dT5_ON
1.7 dT1S5
1.8 T4DHWMAX
1.9 T4DHWMIN
1.10 t_INTERVAL_DHW
1.11 T5S_DISINFECT
1.12 t_DI_HIGHTEMP
1.13 t_DI_MAX
1.14 t_DHWHP_RESTRICT
1.15 t_DHWHP_MAX
1.16 PUMP_D TIMER
1.17 PUMP_D RUNNING TIME
1.18 PUMP_D DISINFECT
1.19 ACS FUNCTION
2 COOL MODE SETTING
2.1 COOL MODE
2.2 t_T4_FRESH_C
2.3 T4CMAX
2.4 T4CMIN
2.5 dT1SC
2.6 dTSC
2.7 t_INTERVAL_C
2.8 T1SetC1
2.9 T1SetC2
2.10 T4C1
2.11 T4C2
2.12 ZONE1 C-EMISSION
2.13 ZONE2 C-EMISSION
3 HEAT MODE SETTING
3.1 HEAT MODE
3.2 t_T4_FRESH_H
3.3 T4HMAX
3.4 T4HMIN
3.5 dT1SH
3.6 dTSH
3.7 t_INTERVAL_H
3.8 T1SetH1
3.9 T1SetH2
3.10 T4H1
3.11 T4H2
3.12 ZONE1 H-EMISSION
3.13 ZONE2 H-EMISSION
3.14 FORCE DEFROST
4 AUTO MODE SETTING
4.1 T4AUTOCMIN
4.2 T4AUTOHMAX
5 TEMP. TYPE SETTING
5.1 WATER FLOW TEMP.
5.2 ROOM TEMP.
5.3 DOUBLE ZONE
6 ROOM THERMOSTAT
6.1 ROOM THERMOSTAT
6.2 MODE SET PRIORITY
47
7 OTHER HEATING SOURCE
7.1 IBH FUNCTION
7.2 IBH LOCATE
7.3 dT1_IBH_ON
7.4 t_IBH_DELAY
7.5 T4_IBH_ON
7.6 P_IBH1
7.7 P_IBH2
7.8 AHS FUNCTION
7.9 AHS_PUMPI CONTROL
7.10 dT1_AHS_ON
7.11 t_AHS_DELAY
7.12 T4_AHS_ON
7.13 EnSWITCHPDC
7.14 GAS_COST
7.15 ELE_COST
7.16 MAX_SETHEATER
7.17 MIN_SETHEATER
7.18 MAX_SIGHEATER
7.19 MIN_SIGHEATER
7.20 TBH FUNCTION
7.21 dT5_TBH_OFF
7.22 t_TBH_DELAY
7.23 T4_TBH_ON
7.24 P_TBH
7.25 SOLAR FUNCTION
7.26 SOLAR CONTROL
7.27 DELTASOL
8 HOLIDAY AWAY SETTING
8.1 T1S_H.A._H
8.2 T5S_H.A._DHW
9 SERVICE CALL
PHONE NO.
MOBILE NO.
10 RESTORE FACTORY SETTINGS
11 TEST RUN
12 SPECIAL FUNCTION
13 AUTO RESTART
13.1 COOL/HEAT MODE
13.2 DHW MODE
14 POWER INPUT LIMITATION
14.1 POWER INPUT LIMITATION
15 INPUT DEFINE
15.1 M1M2
15.2 SMART GRID
15.3 T1T2
15.4 Tbt
15.5 P_X PORT
16 CASCADE SET
16.1 PER_START
16.2 TIME_ADJUST
16.3 ADDRESS RESET
17 HMI ADDRESS SET
17.1 HMI SET
17.2 HMI ADDRESS FOR BMS
17.3 STOP BIT
18 COMMON SET
18.1 t_DELAY PUMP
18.2 t1_ANTILOCK PUMP
18.3 t2_ANTILOCK PUMP RUN
18.4 t1_ANTILOCK SV
18.5 t2_ANTILOCK SV RUN
18.6 Ta_adj.
18.7 F-PIPE LENGTH
18.8 PUMP_I SILENT OUTPUT