Initial Start-Up - Kärcher RCV 5 Bedienungsanleitung

● The cleaning robot does not switch to sleep mode
when it is on the charging station.
● The cleaning robot switches off automatically if it is
in sleep mode for more than 6 hours
Error mode
If the cleaning robot encounters an error during opera-
tion, the display flashes red and a signal sounds.
For a solution, see chapter Troubleshooting guide.
If no action is taken within 5 minutes, the cleaning robot
automatically switches to sleep mode.
"Do not disturb" mode
The "Do not disturb" mode is set by default. In "Do not
disturb" mode, the cleaning robot does not resume an
interrupted cleaning, does not perform scheduled clean-
ing and does not give audible warnings.
"Do not disturb" mode can be deactivated in the App.
Downloading the App is described in the chapter Con-
necting cleaning robots with WLAN and App.

Initial start-up

Setting up the charging station
WARNING
TheRCV 5 cleaning robot may only be charged on the
charger of a charging station with the part number
9.773-014.0.
● Select the location so that the cleaning robot can
easily reach the charging station.
● Ensure a distance of at least 0.5 m to the left and
right of the charging station and a distance of at
least 1.5 m in front of the charging station.
● The location must not be exposed to direct sunlight.
1. Set up the charging station.
Illustration B
2. Plug the mains cable device plug into the cable
holder on the side of the charging station.
Illustration C
3. Connect the mains plug.
Connecting the cleaning robot with the
charging station
Illustration D
1. Place the cleaning robot on the floor in front of the
charging station.
2. Press and hold the on/off switch for 3 seconds.
The cleaning robot switches on.
3. As soon as the display lights up, place the cleaning
robot manually on the charging station and make
sure that the charging contacts have a good contact.
After the initial start-up, the cleaning robot automatically
moves to the charging station.
Connecting cleaning robots with WLAN and
The cleaning robot can be controlled directly via buttons
on the device or via an App using a WLAN-enabled mo-
bile device. To be able to use all available functions we
recommended controlling the cleaning robot via the
Kärcher Home Robots App.
Before you download the App, make sure you have the
following:
● The mobile device is connected to the Internet.
● The 2.4 GHz WLAN of the router is activated.
● Sufficient WLAN coverage is guaranteed.
Download the Kärcher Home Robots App from the Ap-
®
ple App Store or from the Google Play™ store.
18
App
● Google Play™ and Android™ are trademarks or
registered trademarks of Google Inc.
®
● Apple and App store
trademarks of Apple Inc.
The Kärcher Home Robots App offers the following
main functions, among others:
● Mapping of the rooms and several floors
● Setting of time schedules
● Definition of no-go zones and virtual walls
● Notes on faults or malfunctions and the cleaning
progress
● Setting of cleaning preferences (suction modes)
● Establishment of cleaning zones
● Activation/deactivation of the "Do not disturb" mode
● FAQ with detailed troubleshooting
● Contact details for the KÄRCHER Service Centres
Connecting the cleaning robot with the Kärcher
Home Robots App and WLAN:
1. Download the KÄRCHER Home&Garden App from
the Apple App Store or from the Google Play Store.
2. Open the Kärcher Home Robots App.
3. Create an account (if you are not already regis-
tered).
4. Add the desired cleaning robot.
5. Follow the step-by-step instructions in the App.
Installing the dust container
For dry cleaning, remove the wiper cloth and the wiper
cloth holder, see chapter Removing the wiper cloth
holder.
Illustration E
1. Open the cover at the top.
2. Press the dust container into position until it audibly
latches into place.
3. Close the cover at the top.
Removing the dust container
Illustration F
1. Open the cover at the top.
2. Press the clamp.
3. Remove the dust container.
Installing the water reservoir
The water reservoir may contain a small amount of re-
sidual water due to quality control. This is normal.
Illustration G
1. Push the water reservoir horizontally into the clean-
ing robot until it audibly latches into place.
Removing the water reservoir
1. Press any button.
The cleaning robot stops.
English
®
are trademarks or registered
Initial startup