Inhaltsverzeichnis; General Introduction; General Characteristics - Telwin DOCTOR CHARGE 30 Gebrauchsanweisung

2. GENERAL INTRODUCTION ................................... 54
2.1 GENERAL CHARACTERISTICS ....................... 54
2.1.1 CABLE CALIBRATION.............................. 56
2.2 CHARGING PROCESS ..................................... 57
2.2.1 PULSE-TRONIC CHARGE ....................... 57
2.2.2 PROCEDURE ........................................... 58
3. LCD DISPLAY MODELS (BATTERY MANAGER) .. 58
3.1 LCD DISPLAY (Pag. 2) ...................................... 58
3.2 SETTING BATTERY VOLTAGE ......................... 59
3.3 PULSE-TRONIC CHARGE ................................ 59
3.3.1 CHARGE FUNCTION MODES ................. 59
3.3.2 STORING OPERATION SETTINGS ......... 60
3.3.2.1 STORING PULSE-TRONIC
CHARGE ...................................... 60
3.3.2.2 STORING SUPPLY/DIAGNOSTIC
MODE ........................................... 60
3.4 BATTERY AND ALTERNATOR TEST ................ 61
3.4.1 BATTERY TEST ........................................ 61
3.4.2 CHARGE SYSTEM TEST
(ALTERNATOR) ........................................ 61
3.4.3 BATTERY STARTING CHARGE
CAPACITY (CCA) ..................................... 61
3.5 BATTERY MAINTENANCE ................................ 62
3.5.1 DESULFATION ......................................... 62
3.5.2 EQUALIZATION ........................................ 63
3.6 POWER SUPPLY ............................................... 63
3.6.1 DIAGNOSTIC ............................................ 64
3.6.2 SUPPLY .................................................... 65
3.7 START - STARTER AID (if foreseen) ................. 66
3.7.1 Procedure ................................................. 66
3.8 ALARMS ...................................................... 66
4. KEY PAD MODELS (MULTIFUNCTION
BATTERY CHARGER) ............................................ 68
4.1 KEY PAD (Pag. 2) .............................................. 68
4.2 SETTING BATTERY VOLTAGE ......................... 68
4.3 PULSE-TRONIC CHARGE/BOOST ................... 68
4.4 DESULFATION ................................................... 69
4.4.1 Procedure ................................................. 69
4.5 START - STARTER AID (if foreseen) ................. 70
4.5.1 Procedure ................................................. 70
4.6 ALARMS ...................................................... 70
5. INSTALLATION ...................................................... 71
5.1 BATTERY CHARGER POSITION ...................... 71
5.2 CONNECTION TO THE MAINS ......................... 71
6. BATTERY CHARGER PROTECTION ..................... 71
7. USEFUL ADVICE ..................................................... 71
INDEX
EN

2. GENERAL INTRODUCTION

2.1 GENERAL CHARACTERISTICS

MODELS: multifunction electronic battery chargers
for lead batteries with 6/12/24V (6V/3 cells; 12V/6
cells; 24V/12 cells) WET, GEL, AGM, SPIRAL, MF,
PbCa used on vehicle engines (petrol and diesel),
motorcycles, boats etc.
The proposal refers to LCD DISPLAY models and
KEY PAD models.
LCD DISPLAY MODEL
POWER SUPPLY: a 230V 50/60Hz single phase
power supply, with current and charge voltage
maintained constant and controlled electronically.
POWER STREAM TECHNOLOGY
The innovative PowerStream technology used
leads to a marked improvement in performance
compared to traditional battery chargers, up to 50%
higher, thanks to a state-of-the-art charging process
control system, more effi cient power transfer,
quicker recharging times which improves the health
of the battery and extends its working life.
Power Stream
Technology
- 54 -
KEYPAD MODEL
50
+
p e r f o r m a n c e s
TRADITIONAL
BATTERY CHARGER
Traditional
Technology
%