EINHELL mka 2000 e Bedienungsanleitung Seite 19

Anleitung_MKA_2000_E_SPK7:_
When this happens, empty the tray as described
below:
1. Switch off the unit, pull the plug and do not move
the unit.
2. Push a container under the drain screw (1).
3. Unscrew the drain screw (1).
4. Remove the rubber bung (2) from the drain
opening (3).
5. The condensate runs into the container. If the
container is smaller than the condensate tray,
seal the drain opening (3) with the rubber bung
(2) and empty the container. Then repeat the
process from point 4.
6. Once the condensate tray has been completely
emptied, fit the bung (2) and the drainage screw
(1) again.
7. Start the unit again. The "W.F." LED will no
longer flash.
6.10 Draining the condensate with a hose (Fig.
12-14)
ALL THE CONDENSATE MUST HAVE BEEN
DRAINED BEFORE YOU START THE
FOLLOWING PROCESS.
1. Switch off the unit and pull the power plug.
2. Unscrew the drain screw (1).
3. Remove the rubber bung (2) from the drain
opening (3).
4. Connect the condensate drainage hose (4) and
secure it with a clip
5. The drainage hose can be extended with a hose
(5) with a diameter of 18mm. If you do so, make
sure you use a suitable connector.
Note:
The drainage hose must run to the outside with a
slight fall. The "Condensate tray full" indicator is not
operational.
7. Cleaning, maintance and
ordering of spare parts
To avoid an electric shock or risk of fire,
always pull out the mains plug first before
starting any cleaning work .
7.1 Cleaning the air filter (fig. 15)
The air conditioner is fitted with 2 filters.
1. Dust filter (close-meshed filter net)
2. Activated carbon filter (binds particles in the air
and prevents the development of bacteria)
Important: Never use the device without air filters.
12.11.2008 15:28 Uhr Seite 19
1) Dust filter
Remove the filter cover (1 – 3) by pulling it to the
rear.
Then remove the activated carbon filter. Use a
vacuum cleaner or tap the dust filter gently to remove
the dust. If the filter is very dirty, wash it carefully with
warm water. Then allow to dry thoroughly.
2) Activated carbon filter
The activated carbon filter is located behind the top
dust filter and cannot be washed. Its service life is
dependent on the operating conditions. The filter
should be inspected and replaced if necessary. The
filter cover then has to be fitted back on the device
with the activated charcoal filter.
7.2 Cleaning the housing
Use only gentle cleaner and a soft cloth to clean
the housing. Never use aggressive media, petrol,
alcohol or thinner. Only fit the filter back in place
when thoroughly dry.
7.3 At the end of the season
At the end of the season, let the device run for
approx. 3 hours in the fan function (FAN).
Then roll up the power cable and store it in the
storage compartment provided at the back of the
device (fig. 15).
Place a suitable container beneath the
condensate drain and remove the plug. The
trough then empties (see Chapter 6.9).
Re-insert the plug in the condensate drain.
Important: If the plug is not inserted or is not
inserted correctly, water will escape the next time
the device is used again.
Clean the filter and the housing.
Re-insert the filter when thoroughly dry.
Store the device in an upright position, preferably
packed in the original box, in a dry and dust-tight
location.
7.4 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.5 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
GB
19