Available Accessories; Repairs; Environmental Protection; Trouble Shooting - Metabo TS 250 Originalbetriebsanleitung

curved board on the table with the
convex side up).
•
To simplify repetitive cut-off work
use a stock stop .
•
Keep surface of table clean.

11. Available Accessories

For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A
Floor Stand
Provides for a secure machine
stand and optimal working height;
ideal in mobile use, folds up for sav-
ing space.
B
Dust Collection Attachment
Helps to protect your health and to
keep the shop clean.
C
Roller/Ball Transfer Stand
For accurate guiding of long stock.
D
TCT Saw Blade
250 x 2.8/1.8 x 30, 60 ATB teeth,
15° rake, 2 pinholes
For rip and cross cuts in grown tim-
ber and particle board.
E
TCT Saw Blade
250 x 2.8/1.8 x 30, 80 ATB teeth,
10° rake, 2 pinholes
For rip and cross cuts in panels;
plastic, aluminium, copper extru-
sions and high-grade veneered
sheets.
F
TCT Saw Blade
250 x 2.8/2.0 x 30, 80 square/trap-
ezoidal teeth, 5° negative rake, 2
pinholes
General purpose blade for plastics,
thin-walled aluminium-,

15. Technical specifications

Voltage
Wattage power input P1
power output P
Current draw
Fuse protection min.
Protection class
Rated no-load speed (at 230V)
Cutting speed (at 230V)
Saw blade diameter (outer)
Saw blade arbor bore diameter (inner)
Kerf width
Depth of cut with saw blade vertical
at 45° saw blade tilt
brass- and steel extrusions as well
as for
veneered sheets.

12. Repairs

A Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.

13. Environmental Protection

The machine's packing can be 100%
recycled.
Worn out power tools and accessories
contain considerable amounts of valua-
ble raw and rubber materials, which can
be recycled.
These instructions are printed on paper
produced with elemental chlorine-free
bleaching process.

14. Trouble Shooting

A
Danger!
Before carrying out any fault service
or maintenance work, always:
1. switch machine OFF;
2. unplug power cable;
3. wait for saw blade to come to
copper-,
standstill.
2
panels, laminates and
V
kW
kW
A
A
-1
min
m/s
mm
mm
mm
mm
mm
ENGLISH
Check that all safety devices are
operational again after each fault
service.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
•
Restart machine.
No mains voltage
•
Check cables, plug, outlet and
mains fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
•
Remove cause for overheating, let
cool off for a few minutes. Then
press Reset button and restart
machine.
Stated top speed is not reached
Motor supply voltage too low:
•
use a shorter extension cable or
extension cable with larger lead
cross section (≥ 1.5 mm
•
Have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
•
Replace saw blade (see chapter
"Maintenance").
Dust spout blocked
No dust collector connected or suction
capacity insufficient:
•
connect dust collector, or
•
increase suction capacity (air speed
≥ 20 m/sec at chip ejection tube).
230 (1∼ 50 Hz) 110 V (1∼ 50 Hz)
2.0 kW S6 40% 1.55 kW S6 40%
1.2 kW S6 40% 0.84 kW S6 40%
9.6 15.5
16 (time-lag) –
IP 20 IP 20
3950 3900
51.7 50.1
250 250
30 30
2.8 2.8
0 ... 77 0 ... 77
0 ... 51 0 ... 51
2
).
23