Specifications - Hitachi C 10FCB Bedienungsanleitung

4. Always keep the saw blade sharp. Observe the
maximum speed marked on the saw blade.
5. Do not use saw blades which are damaged or
deformed.
6. Do not use saw blades made of high speed steel.
7. Use only saw blades recommended by HITACHI.
8. The saw blades should be from 235 mm to 260 mm
external diameter ranges.
9. Select saw blades in relation to the material to be
cut.
10. Never operate the compound saw with the saw
blade turned upward or to the side.
11. Ensure that the workpiece is free of foreign matter
such as nails.
12. Replace table insert when worn.
13. Do not use the saw to cut other than aluminium,
wood or similar materials.

SPECIFICATIONS

Max. Cutting
Capacity
Height x Width
Saw Blade Dimensions (oD × iD × Thickness)
Miter Cutting Angle
Bevel Cutting Angle
Power Input
No-Load Speed
Machine Dimensions (Width × Depth × Height)
Weight (Net)
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) 255 mm TCT Saw blade ............................................. 1
(2) Dust bag ...................................................................... 1
(3) 10 mm Box wrench .................................................... 1
(4) Vise Assembly ............................................................ 1
(5) Collar (A) (mount on tool) .......................................... 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (SOLD SEPARATELY)
(1) Extension Holder and Stopper
(2) Saw blade 255 mm TCT Saw blade for fine surface
(Total teeth:60)
(3) Saw blade 255 mm TCT Saw blade for normal cut
(Total teeth:70)
Optional accessories are subject to change without notice.
APPLICATION
Cutting various types of alminium sach and wood.
UNPACKING
Carefully unpack the power tool and all related items
(standard accessories).
Check carefully to make certain all related items
(standard accessories) are present.
0°
Miter 45°
Bevel 45°
Miter + Bevel 45°
14. Connect compound saw to a dust collecting device
when sawing.
The operator is informed of factors that influence
exposure of dust e.g. type of material being
machinered and importance of local extraction
(capture or source) and proper adjustment of hoods/
baffles/chutes.
15. Take care when slotting.
16. When transporting or carrying the tool, do not grasp
the holder and the guard. Grasp the handle instead
of the holder and the guard.
17. Start cutting only after motor revolution reaches
maximum speed.
18. Promptly cut OFF the switch when abnormality ob-
served.
19. Shut off power and wait for saw balde to stop before
servicing or adjusting tool.
20. During a miter or bevel cut the blade should not be
lifted until it has stopped rotation completely.
59 mm × 144 mm (89 mm × 101 mm)
59 mm × 102 mm (89 mm × 70 mm)
41 mm × 144 mm
41 mm × 102 mm (44 mm × 89 mm)
255 mm × 30 mm × 2.7 mm
Right 0° – 60°, Left 0° – 45°
Left 0° – 45°
1640W*
4900 min
547 mm × 592 mm × 581 mm
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is conencted to a receptacle while the trigger
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extention cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be kept
as short as practicable.
4. When the power tool is prepared for shipping, its
main parts are secured by a locking pin.
Move the handle slightly so that the locking pin can
be disengaged.
During transport, lock the locking pin into the gear
case. (Fig. 2)
5. Attach the dust bag to the main unit (Fig. 1)
6. Attach the side handle to the turntable (Fig. 1)
7. Installation
Attach the power tool to a level, horizontal work bench.
Select 8 mm diameter bolts suitable in length for the
thickness of the work bench.
English
-1
14 kg
6