Specifications - Hitachi CS 30SB Bedienungsanleitung

English
18. Do not switch the unit on while the chain case is
attached.
Injury may occur.
19. Ensure there are no nails and other foreign objects in
the material.
If the saw chain impact on the nail etc., injury may
occur.
20. To avoid the guide bar becoming entangled with the
material when chopping on a verge or when subject to
the weight of material while cutting, install a supporting
platform close to the cutting position.
If the guide bar becomes entangled, injury may occur.
21. If the unit is to be transported or stored after use, either
remove the saw chain, or attach the chain cover.
If the saw chain comes into contact with your body,
injury may occur.
22. Adequately care for the unit.
○ To ensure work can be performed safely and effi ciently,
care for the saw chain to ensure it provides optimal
cutting performance.
○ When replacing the saw chain or guide bar, maintaining
the body, fi lling oil etc., follow the instruction manual.
DESCRIPTION OF NUMBERED ITEMS (Fig. 2 - Fig. 38)
1 Kickback zone
2 Chain brake
3 Free
4 Lock
5 Knob
6 Tension dial
7 Side cover
8 Guide bar
9 Saw chain
0 Guide bar tip
! Sprocket

SPECIFICATIONS

Model
Guide bar length (Max. cutting length)
Guide bar Type
Voltage (by areas)*
1
Power Input*
1
No-load chain speed
Type of chain
Chain pitch / Gauge
Sprocket
Oil pump
Chain oil tank capacity
Overload protection
Chain brake
Weight*
2
*1 Be sure to check the nameplate on product as it is subject to change by areas.
*2 Weight: According to EPTA-Procedure 01/2003
@ Blade direction
# Chain tensioner hole
$ Chain tensioner boss
% Increase the tension
^ Decrease the tension
& Drive link
* Fasten
( Pull
) Actuation
q Release
w Chain oil
CS30SB
300 mm
P012-50CR
91PX-45 (Oregon)
4.7 kg
23. Ask the shop to repair the unit.
○ Do not modify this product, since it already complies
with the applicable safety standards.
○ Always refer to your Hitachi Authorized Service Center
for all repairs.
Attempting to repair the unit yourself may result in an
accident or injury.
24. When not using the unit, ensure it is properly stored.
Drain off the chain oil, and keep in a dry place out of
reach of children or a locked location.
25. If the warning label is no longer visible, peels off or is
otherwise unclear, apply a new warning label.
For the warning label, refer to your Hitachi Authorized
Service Center.
26. When working, if local rules or regulations apply,
comply with the same.
27. Recommendation for the use of a residual current
device with a tripping current of 30 mA or less
28. Statement to position the cord of so that it will not be
caught on branches and the like, during cutting
29. Recommendation that the fi rst-time user should, as
a minimum practice, cutting logs on a saw-horse or
cradle
e Oil sight glass
r Oil pump adjuster
t Lock-off button
y Switch
u Plug clip
i Plug
o Extension cord
p Spiked bumper
a Front handle
s Rear handle
d Round fi le
CS35SB
350 mm
P014-50CR
(220 V, 230 V, 240 V)
1900 W
14.5 m/s
91PX-52 (Oregon)
9.53 mm (3/8") / 1.27 mm (0.05")
Number of teeth: 6
Automatic
200 ml
Electrical
Manually actuated
4.8 kg
8
f 1/5 of diameter of fi le
g Depth gage jointer
h Flat fi le
j Protruding depth gage
head
k Round off
l Brake band chamber
; Chain oil spout
z Groove
x Oil hole
c Chain catcher
CS40SB
400 mm
P016-50CR
91PX-57 (Oregon)
4.9 kg