Kärcher SC 4 Deluxe EasyFix Iron Originalbetriebsanleitung Seite 14

Steam lever
16
Unlocking button
17
Child lock
18
Steam hose
19
Steam Connector
20
Spotlight nozzle
21
Round brush (small)
22
**Round brush (large)
23
**Power nozzle
24
Crevice brush
25
Manual nozzle
26
Manual nozzle microfibre cover
27
Extension tubes (2 x)
28
Unlocking button
29
Floor nozzle
30
Hook and loop fastener
31
Microfibre floor cloth (1 x)
32
**Microfibre floor cloth (2 x)
33
**Carpet glider
34
Descaler
35
Steam pressure iron
36
Indicator light (orange) - heating
37
Steam switch (bottom)
38
Steam connector
39
**SC 4 Deluxe EasyFix Iron Premium
Installation
Installing accessories
1. Open the cover on the device socket.
Illustration B
2. Connect the steam connector to the device socket
so that the steam connector audibly engages.
Illustration B
3. Push the open end of the accessory onto the steam
gun so that the unlocking button on the steam gun
engages.
Illustration G
4. Push the open end of the accessory onto the spot-
light nozzle.
Illustration H
5. Connect the extension tubes with the steam gun.
a Push the 1st extension tube onto the steam gun
so that the unlocking button on the steam gun en-
gages.
The connection pipe is connected.
b Push the 2nd extension tube onto the
1st extension tube.
The connection pipes are connected.
Illustration I
6. Push the accessory and / or the floor nozzle onto the
free end of the extension tube.
Illustration J
The accessory is connected.
Disconnecting accessories
1. Move the child lock back.
The steam lever is locked.
2. Push the cover on the device socket down and dis-
connect the steam connector from the device sock-
et.
3. Press the unlocking button and pull the parts apart.
Illustration O
The water reservoir can be removed at any time for fill-
ing or be filled directly at the device.
ATTENTION
Damage to the device
Unsuitable water can block the nozzles or damage the
water level indicator.
Do not fill in pure distilled water. Use a maximum of 50%
distilled water mixed with tap water.
Do not use condensation from the clothes dryer for fill-
ing.
Do not use collected rain water for filling.
Do not use cleaning agents or other additives (e.g.
scents) for filling.
Removing the water reservoir for filling
1. Pull the water reservoir vertically upwards.
Illustration C
2. Fill the water tank vertically with tap water or a mix-
ture of tap water and no more than 50% distilled wa-
ter.
3. Insert the water reservoir and press downwards until
it locks into place.
Filling the water reservoir directly on the device
1. Fill tap water or a mixture of tap water and no more
than 50% distilled water from a vessel into the filling
hole of the water reservoir up to the "MAX" mark.
Illustration D
Switching on the device
Note
If there is no or too little water in the steam boiler, the
water pump starts to run and pumps water from the wa-
ter reservoir into the steam boiler. The filling process
can take several minutes.
Note
The device briefly closes the valve every 60 seconds
causing an audible soft click. Closing prevents the valve
from clogging. This does not affect the steam output.
1. Place the device on a firm surface.
2. Insert the main plug into a socket.
3. Turn the selector switch from the OFF position to the
steam setting selection range.
Illustration E
The LED strip is in fading red.
4. The LED light lights up a continuous green after ap-
prox. 3 minutes.The device is ready for use.
Illustration F
5. Press the steam lever.
Illustration G
Steam leaks out.
Regulating the steam volume
The expelled steam volume is regulated using the se-
lector switch for steam volume. The selector switch has
three positions.
English
Operation
Filling water
13