Diagnostic Buffer; Rs485 Cable Installation; Connection Configurations; Connection C - Electrical - Agilent Technologies TV 301-P Bedienungshandbuch

Diagnostic buffer

OFF
MEANING
SET
0 B station non exist (set by master)
0
B station not ready (slave not ready for
1
data exchange)
B cfg fault (configuration data doesn't
2
match)
B ext diag (slave has external diagnostic data)
3
B not supported (slave doesn't support re-
4
quested function)
B invalid slave response ( slave sets per-
5
manent '0')
B prm fault (wrong parameter assignment)
6
B master_lock (slave is parameterised by
7
another master)
1 B prm req (slave has to be re-
0
parameterised)
B stat diag (static diagnosis)
1
B fixed '1'
2
B wd_on (response monitoring active)
3
B Freeze mode (received freeze command)
4
B Synch mode (received synch command)
5
B reserved
6
B diag deactivated (slave is parameter-
7
ised by another master)
2 Reserved
3
Master Add (master address after parameter-
isation. FF= without parameter)
4 Ident number high
5 Ident number low
6 External diagnosis "Header" length indication in-
cluding header
7 Interface Status
B Controller not responds
0
B Controller not identified
1
B Input data not fully coherent yet
2
B Not used
3
B Not used
4-7
8 B – Start/Stop diag status
7-4
B – Low Speed diag status
3-0
9 B – Soft Start diag status
7-4
B – Active Stop diag status
3-0
10 B – Vent Valve diag status
7-4
B – Purge diag status
3-0
11 B – Heather Jacket diag status
7-4
B – Stop Speed Reading diag status
3-0
12 B – High speed setting diag status
7-4
B – Low speed setting diag status
3-0
13 B – Water Cooling Max Temp diag status
7-4
B – Water Cooling Hyst diag status
3-0
14 B – Set Point Hyst diag status
7-4
B – Heather Jacket Setting diag status
3-0
15 B – Flow Meter Threshold diag status
7-4
B – Reserved diag status
3-0
16 B – Set Point Value diag status
7-4
B – Set Point Delay diag status
3-0
17 B – Vent Valve Open Delay diag status
7-4
B – Vent Open Time diag status
3-0
18 B – Vent/Purge Auto/Man diag status
7-4
B – Vent/Purge Remote/Profibus diag status
3-0
19 B – Interlock Mode diag status
7-4
B – Set Point Logic diag status
3-0
20 B – Heather Jacket Mode diag status
7-4
B – Load Gas Type diag status
3-0
21 B – Purge Gas Type diag status
7-4
B – Start/Stop/Interlock Mode diag status
3-0
22 B – Set Point Type diag status
7-4
B – Analog Out Type
3-0
23 B – Reserved
7-4
B – Reserved
3-0

RS485 CABLE INSTALLATION

The supplied serial cable must be installed when the
TV 301-P Navigator Controller have to be controlled by
means of a remote computer.
The cable is installed fixing the 9 pin D-type connector
into the P2 serial connector as shown in the following
figure.

CONNECTION CONFIGURATIONS

Connection C - ELECTRICAL

The turbopump is connected to the controller through an
6-pin connector. Pins B, C and D are the 3-phase
supply to the motor, pins A and F are connected to the
temperature sensor (NTC type, 30 KΩ resistance
at 25° C) and pin E is connected to the pump ground.
If the temperature sensor is disconnected, the pump will
not start. To prevent damage to the pump when the
temperature exceeds 60° C, the sensor automatically
cuts out the power supply.

ACCESSORIES AND SPARE PARTS

DESCRIPTION
Serial cable and Navigator
Software
Fan extension cable
50
TECHNICAL INFORMATION
PART NUMBER
969-9883
969-9949
87-901-001-01 (A)