Inhaltsverzeichnis
Werbung
1 '
TYPE
ART.NR
V~
W
r/min mm
327210 KZ-210
230
1050
4.500
UK
English
Product: Ferm Cutting-off machine
Type KZ-210, Article nr 327210
Ferm, Genemuiden, The Netherlands
Sound-pressure level (L pa )
91,2 dB(A)
Sound-pressure cap. level (L wa )
104,2 dB(A)
Vibrations unloaded (ã w )
2,5 m/s
SERIAL NUMBER
The serial number on the machine is composed as fol-
lows.
Serial nr.
ORDER NUMBER YEAR OF CONSTRUCTION
FIRST READ THESE INSTRUCTIONS FOR
USE PROPERLY BEFORE PUTTING THE
CUTTING-OFF MACHINE INTO USE.
1. SPECIAL SAFETY INSTRUCTIONS
BEFORE EACH USE
1. Check the cutting-off machine. If any part of the cut-
ting-off machine is missing, bent or unusable in anot-
her way, or if electrical faults occur, switch off the ma-
chine and remove the plug from the socket. Replace
all missing, damaged or faulty parts, before using the
machine again.
2. Make sure that hands, eyes, face and ears are well pro-
tected.
-
Use of safety goggles without the CE quality mark can
lead to serious injury if the glass breaks.
-
In order to prevent the saw blade from becoming
jammed in the saw cut and workpieces being flung
away, the instructions below must be followed:
- Choose a suitable saw blade for the work.
Only use the cutting-off machine to saw wood and
derived products, or light metals such as alumini-
um. Other materials can be flung away, get caught
in the saw blade or cause other dangers.
- The arrow on the saw blade, which indicates the di-
2
90°
45°
kg.
mm
mm
BJ 2000
mm
mm
kg
210x18 120x60 70x60
7,2
rection of rotation, must point in the same direc-
tion as the arrow placed on the machine. The saw
blade teeth must point downwards on the front of
the saw.
- Check whether the saw blade is sharp, undamaged
and well aligned. Press the saw head downwards
after removing the plug.
Turn the saw blade by hand and see whether it
turns freely. Put the machine in the 45° position
and repeat the test. If the saw blade touches any-
where, it must be adjusted again.
2
- Keep the saw blade and the tensioning surfaces of
the clamps clean.
- The saw blade flange must always be mounted with
the tightened recess towards the saw blade.
- The flange screw must be tightened with a 13 mm
open-end wrench.
- Check whether all the tensioning devices and in-
terlocks are secure and that no single part shows
too great a clearance.
- Never use just your hands for sawing.
- Always secure the workpiece against the check, so
that it cannot topple or turn during sawing. No im-
purities may be allowed to gather under the work-
piece.
- Make sure that the workpiece cannot move after
being sawn through, for example, because it is not
supported by the full surface.
- For sawing workpieces which are not being sup-
ported by the full surface, use fillings or another
machine.
-
Check whether the sawn off pieces can be removed
laterally from the saw blade. Otherwise they can be
caught by the saw blade and flung away.
-
Never saw several workpieces at the same time.
-
Be especially careful when sawing large, very small or
awkwardly shaped workpieces.
-
Be careful when double mitring.
- Use additional supports (tables, trestle or other)
for long workpieces, which will otherwise topple
from the machine table if they are not held.
- Do not use the machine to saw workpieces which
are so small that they can no longer be held safely.
- When sawing profile sections, work must be car-
ried out so that the workpiece cannot slide away
and the saw blade cannot become jammed. A profi-
led workpiece must lie flat or be held by an auxiliary
EXPL0DED VIEW KZ-210
Ferm
Ferm
43
Werbung
Inhaltsverzeichnis
