Inhaltsverzeichnis
Werbung
MILJØ
For at undgå transportskader leveres maskinen i en solid
kasse. Emballagen er så vidt muligt fremstillet af
genbrugsmateriale, så sørg for, at emballagen afleveres
til en genbrugsplads. Når maskinen skal kasseres, skal
man tage den med til den lokale Ferm forhandler. Her
sørges der for miljøvenlig bortskaffelse af maskinen.
GARANTI
Garantibetingelserne findes på garantibeviset bag i
denne brugsanvisning.
ı
( DK )
CE
KONFORMITETSERKLÆRING
Hermed bekræfter vi på eget ansvar, at dette produkt er
i overensstemmelse med følgende standarder eller
relaterede dokumenter:
EN61029-1, EN61029-2-9, EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
i overensstemmelse med bestemmelserne i
direktiverne:
98/37/EEC, 73/23/EEC, 89/336/EEC
fra 01-01-2009
ZWOLLE NL
J.A. Bakker - van Ingen
J.F.J. Strikkers
CEO Ferm BV
Senior Quality Manager Ferm BV
Det er vores politik fortsæt at forbedre vores
produkter, og derfor forbeholder vi retten til at ændre
produktspecifikationer uden forud bemærkning.
Ferm BV • Lingenstraat 6 • 8028 PM • Zwolle
The Netherlands
56
defect occurs, turn the machine off and take the plug out
of the socket. Replace all missing, damaged or defective
parts before using the machine again.
To fix the saw blade in the slot and to prevent the piece
of work from moving, follow the instructions below.
•
Choose a suitable saw blade for the work. Use the
crosscut saw only for sawing wood and wood
derivatives or light metal such as aluminium. Other
materials can jump away or get caught in the saw
blade or give rise to other dangers.
•
The arrow marked on the saw blade, which indicates
the direction of rotation, must point in the same
direction as the arrow marked on the machine. The
saw blade teeth must point downwards on the front
of the saw.
•
Check that the saw blade is sharp, undamaged and
correctly aligned. After unplugging the machine, push
the saw hood downwards. Rotate the saw blade by
hand and check that it revolves freely. Put the
machine in the 45° position and check free rotation
again. If the blade touches anything it must be
adjusted.
•
Keep the saw blade and the clamping surface for the
clamps clean.
•
The saw blade flange must always be mounted with
the notch tightened towards the saw blade.
•
Check that all tensioning devices and locks are
secure and that no part has too much play in it.
•
Never just use your hands for sawing.
•
Always press the piece of work firmly against the
stop, so that it cannot tilt or turn while sawing. No
impurities must gather underneath the piece of work
being sawn.
•
Make sure that the piece of work cannot move after
being sawn, for example because it is not completely
supported by the surface of the machine.
•
For sawing pieces of work that are not supported by
the full surface, use some padding or another
machine.
•
Replace any worn-out table inserts.
•
Only use saw blades recommended by the
manufacturer (EN-847-1).
•
Never use HS (High Speed) saw blades.
•
Check that the sawn off bits can be removed
sideways from the saw blade, otherwise they can get
caught on the blade and flung about.
•
Never saw more than one piece of work at the same
time.
•
Be extremely careful when sawing large, very small
or awkward pieces of work.
•
Be careful when sawing double mitre joints.
•
Use additional supports (tables, sheer-legs and the
like) for long pieces of work that can tip over and
topple off the machine if they are not properly
secured.
•
Never use the machine to saw pieces of work that
are so small that they cannot be secured safely.
•
When sawing profile sections the work must be
carried out such that the piece of work cannot slide
away and the saw blade cannot become jammed. A
profiled piece of work must lie flat or be held in place
by an attachment so that toppling or sliding during
the work is prevented.
•
Round pieces of work such as tubes must be well
Ferm
Ferm
secured, otherwise these can revolve and the danger
exists that the saw blade catches in them. Always
keep the piece of work on the table and against the
stop using a suitable accessory or attachment.
•
Make sure that the piece of work does not have any
nails or other foreign objects in it.
USER SAFETY
•
Make sure you have a clean and tidy working
environment.
•
Make sure the working environment is well lit.
•
The user of the machine must be instructed in the use,
adjustment and operation of the machine.
•
Use a dust mask or dust hood to prevent the inhalation
of (harmful) dust.
•
Wear gloves when you exchange the saw blade or
when rough material is to be sawn. It is best to keep saw
blades in a separate holder to prevent anyone getting
hurt.
•
When the machine is equipped with a laser, this may
not be replaced by a different type of laser. Repairs may
only be carried out by the laser manufacturer or a
recognised specialist.
•
The operator should wear ear protectors to reduce
any damage to hearing.
•
To prevent accidents occurring by the accidental
switching on of the machine, the plug must always be
pulled out of the socket before adjustment of the stop
or the saw head is carried out, when changing blades or
accessories, and when maintaining the machine.
•
To prevent electric shocks, when plugging the plug into
the socket the metal pins must not be touched in any
way whatsoever.
•
Never use the cord to pull the plug out of the socket.
Keep the cord away from oil, heat and sharp objects.
•
Never apply a cleaning or lubrication agent to a saw
blade that is still revolving.
•
To prevent fires, never use the machine in the vicinity
of flammable liquids, vapours or gases.
•
Always use original accessories: others may cause
wounding.
•
Always choose the right saw blade in relation to the
material to be sawn.
•
Ensure that during operation, the swinging guard
functions properly. It must move freely and be able to
close by itself. It should never be jammed in the open
position.
•
Do not work with material containing asbestos.
•
Protect the saw blade from strikes and shocks. Do not
apply side pressure to the saw blade.
TRANSPORT
Before all work on the machine, pull the mains plug.
Check that all locks and tensioning devices are secure:
•
Turn the locking knob on the turntable
counterclockwise.
•
Slide the machine completely towards yourself
•
Turn the locking knob on the turntable clockwise to
lock the slide-function
•
Unlock the pin on the right hand side of the machine
•
Push the button in the handgrip to unlock the saw
blade protection
5
Werbung
Inhaltsverzeichnis
