Electrical Safety; Assembly And Adjustments; Unpacking - DeWalt DW743N QS Originalanweisungen

EN G LI S H
22 Bevel clamp handle
BENCH SAW MODE
A3
22 Bevel clamp handle
23 Height adjuster
24 Bench saw table
25 Upper blade guard
26 Parallel fence
27 Mitre fence (option)
OPTIONAL ACCESSORIES
For use in mitre saw mode:
A4
28 Adjustable stand 760 mm (max. height) (DE3474)
29 Support guide rails 1,000 mm (DE3494)
29 Support guide rails 500 mm (DE3491)
30 Swivelling stop (DE3462)
31 Length stop for short workpieces (to be used with guide rails [29])
(DE3460)
32 Support with removable stop (DE3495)
33 Support with stop removed (DE3495)
34 Material clamp (DE3461)
A5
35 Roller support table (DE3497)
For use in bench saw mode:
A3
27 Mitre fence (DE3496)
A6
36 Extension table (DE3472)
A7
37 Single sliding table (DE3471)
Not shown
– Double sliding table
For use in all modes:
A8
38 Three way dust extraction kit (DE3500)
INTENDED USE
Your D WALT flip-over saw has been designed to operate as a mitre
E
saw or saw bench to perform the four main sawing operations of
ripping, cross-cutting, bevelling and mitring easily, accurately and safely.
This unit is designed for use with a nominal blade diameter 250 mm
carbide tip blade for professional cutting wood, wood products and
plastics.
MITRE SAW MODE
In mitre saw mode, the sawing machine is used in vertical, mitre or
bevel position.
BENCH SAW MODE
Turned over on its central axis, the sawing machine is used to perform
the standard ripping operation and for sawing wide pieces by manually
feeding the workpiece into the blade.
WARNING: Do not use the machine for other purposes as
described.
• This product is not intended for use by persons (including children)
suffering from diminished physical, sensory or mental abilities; lack
of experience, knowledge or skills unless they are supervised by
a person responsible for their safety. Children should never be left
alone with this product.
36

Electrical Safety

The electric motor has been designed for one voltage only. Always
check that the power supply corresponds to the voltage on the rating
plate.
This machine is of Class I construction; therefore earthed (grounded)
connection is required.
WARNING: 115 V units have to be operated via a fail-safe
isolating transformer with an earth screen between the
primary and secondary winding.
If the supply cord is damaged, it must be replaced by a specially
prepared cord available through the D
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.
• Connect yellow/green lead to the earth terminal
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug should be fitted by a competent person. If you are in
doubt, contact an authorized D
electrician.
• The plug fitted should comply with BS EN60309 (BS4343),
16 Amps, earthing contact position 4h.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension
cable suitable for the power input of this tool (see Technical Data).The
minimum conductor size is 1.5 mm
When using a cable reel, always unwind the cable completely.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting
or changing set-ups or when making repairs. Be sure
the trigger switch is in the OFF position. An accidental start-
up can cause injury.

Unpacking

WARNING: When moving the machine, always seek
assistance. The machine is too heavy for one person to
handle.
• Remove the loose packaging material from the box.
• Lift the machine out of the box.
• Remove the parts box from the interior of the machine.
• Remove any remaining packing material from the machine.
Mounting the Legs (fi g. C1)
With the legs mounted, the machine is suitable for stand-alone
placement.
• Turn the machine upside down.
• Pass a coach bolt (47) from the flat side through the holes into
each of the legs (18).
• Place a lock knob (48) and washer (49) onto the bolts.
• Present a leg (18) to each of the mounting points (46) located at
the edges on the inside of the base. For each leg, make sure that
the lock knob and washer locate at the outside of the open ended
slot.
• Tighten the lock knobs.
WALT service organisation.
E
WALT repair agent or qualified
E
; the maximum length is 30 m.
2