Residual Current Device - DeWalt D24000 Originalanweisungen

E N G L I S H
• Connect the blue lead to the neutral terminal.
• Connect the yellow/green lead to the earth terminal
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
WARNING: Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or .
Fitting a Mains Plug to 115 V Units
(U.K. and Ireland Only)
• The plug should be fitted by a competent person. If you are in doubt,
contact an authorized D WALT repair agent or a qualified electrician.
E
• The plug fitted should be comply with BS EN 60309 (BS4343),
16 Amps, earthing contact position 4h.
Using an Extension Cable
If an extension cable is required, use an approved 3–core extension cable
suitable for the power input of this tool (see technical data).The minimum
2
conductor size is 1.5 mm ; the maximum length is 30 m.
When using a cable reel, always unwind the cable completely.

Residual Current Device

The machine is equipped with a residual current device (RCD), which
protects the user against electric shock by interrupting the circuit when a
leakage current of 30 mA or greater is detected. For 115 V units the rated
leakage current is 5 mA.
WARNING: Never operate the machine without the RCD in
place. Do not use the machine if the RCD does not function
properly. For the RCD to work, the machine must be connected
to an earthed wall socket. Periodically check the function of the
RCD, pressing the TEST button.
Assembly
WARNING: Prior to assembly always unplug the tool.
WARNING: When assembling the machine, always follow the
instructions in the order as described below.
Unpacking the machine and its parts
WARNING: When moving the machine, always seek
assistance. The machine is too heavy for one person to
handle.
• Remove the loose packaging material from the box.
• Lift the machine parts out of the box.
• Remove any remaining packing material from the machine parts.
Mounting the motor frame to the support frame (fi g. B1)
• Place the support frame (16) on a relatively smooth and level surface.
• Place the motor frame (17) on the support frame aligning the holes in
the foot (18) with the mounting holes (19).
• Insert a screw (20) into the holes.
• Tighten the screws using the hex key (21) provided.
Mounting the sliding table to the support frame assembly (fi g. B2 & B3)
• Make sure the lock (22) is in the unlock position.
• Hold the table in front of the frame, aligning the rollers (23) with the
roller rail (24).
• Place the rear roller onto the round rail.
• Slide the table onto the rail, making sure that the bearings (25) locate in
the slide rails (26).
• When the front of the table is approaching the frame, tilt the table
slightly to clear the stop (27).
36
• Lock the table in position by rotating the pin (22) and pushing it into the
hole (28) in the rail.
Placing the machine into the water basin (fi g. B4)
• Place the water basin (13) on a relatively smooth and level surface.
• Fit the plug (29) into the drain hole.
• Lift and hold the machine at the carrying points as shown.
• Lower the machine into the water basin as shown.
Mounting the extension table (fi g. C)
• Hold the extension table (6) in front of the right-hand side of the sliding
table (4).
• Align the positioning pins (30) on the extension with the holes (31) in
the sliding table.
• Place the extension against the sliding table.
• Tighten the clamp knob (32).
Installing the water pump (fi g. D1 & D2)
• Fit the hose (33) onto the fi tting (34).
• Place the water pump (35) in the deep corner of the water basin (13).
• Route the power cable and the water tube over the bottom of the
water basin as to avoid them from getting caught up by the sliding
table.
Mounting the water collectors (fi g. E1 & E2)
Rear water collector
The rear water collector (15) collects water run-off when cutting large
workpieces.
• Hold the water collector in position to the rear of the water basin.
• Slide the arms (36) underneath the edges (37) of the water basin until
the recesses (38) locate behind the lugs.
• Tilt the rear of the water collector slightly until the collector snaps in
position.
Sliding table water collector
The sliding table water collector (14) travels with the table and collects
water run-off from large tiles and diagonal cuts.
• Hold the water collector in position to the right-hand side of the sliding
table.
• Slide the arms (39) underneath the edges (40) of the sliding table until
the recesses (41) locate behind the lugs.
• Tilt the rear of the water collector slightly until the collector snaps in
position.
Mounting the cutting disc (fi g. F1 – F3)
The maximum diameter cutting disc that can be fi tted is 254 mm.
• Using the Hex key (42) supplied, loosen the screw (43) on the side of
the guard.
• Pull back the rubber side fl ap (44) and lift the guard (9) towards the rear.
• Depress the spindle lock button (45) with one hand, then take the
supplied spanner (46) in the other hand to loosen the locking nut (47)
by turning counterclockwise.
WARNING: To use the spindle lock, press the button as shown
and rotate the spindle by hand until you feel the lock engage.
Continue to hold the lock button in to keep the spindle from
turning.
• Remove the locking nut (47) and the outside fl ange collar (48).
• Install the cutting disc with the arrow facing the same way as the arrow
on the guard.
• Replace the outer fl ange collar (48). Refer to Material Thickness for
proper fl ange use.