Residual Risks - DeWalt DWE46172 Bersetzt Von Den Originalanweisungen

Weight
EngLIsh
5) Service
a ) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Surface Grinding Shroud Safety Rules
• The shroud must be securely attached to the power tool
and positioned for maximum safety, so the least amount
of wheel is exposed towards the operator. The shroud is
designed to collect dust and help protect the operator from
accidental contact with the wheel.
• Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.
• Only use dry diamond surface cup wheels with this
surface grinding shroud. The surface grinding shroud is
not intended to be used with standard grinding, cut-off, cup
wheels or wire brushes.
• The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can break
and fly apart.
• Hold power tool by insulated gripping surfaces only,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and shock the operator.
• Always use side handle. Tighten the handle securely. The
side handle should always be used to maintain control of the
tool at all times.
• Do not use a damaged accessory. Before each use
inspect the accessory such as diamond wheel for chips
and cracks, backing pad for cracks and tear or excess
wear. If power tool or accessory is dropped, inspect
for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself
and bystanders away from the plane of the rotating
accessory and run the power tool at maximum no-load
speed for one minute. Damaged accessories will normally
break apart during this test time.
• When starting the tool with a new or replacement
wheel, hold the tool in a well protected area and let it
run for one minute. If the wheel has an undetected crack
or flaw, it should burst in less than one minute. Never start
the tool with a person in line with the wheel. This includes
the operator.
• Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments. The
eye protection must be capable of stopping flying debris
generated by various operations. The dust mask or respirator
14
must be capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity noise may
cause hearing loss.
Position the cord clear of the spinning accessory. If you
•
lose control, the cord may be cut or snagged and your hand or
arm may be pulled into the spinning accessory.
• Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may grab
the surface and pull the power tool out of your control.
• Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could snag
your clothing, pulling the accessory into your body.
• Regularly clean the power tool's air vents. The
motor's fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
• Do not operate the power tool near flammable
materials. Sparks could ignite these materials.
Do not use accessories that require liquid coolants. Using
•
water or other liquid coolants may result in electrocution
or shock.
• DO NOT use wire brushes with this surface
grinding shroud.
• DO NOT use abrasive wheels.
• DO NOT grind or cut metal with a diamond cup wheel.
Fragments could loosen and fly apart.
• ALWAYS use with a dust collector.

WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or dust
mask if cutting operation is dusty. ALWAYS wear certified
safety equipment.

WARNING: Before beginning the work, check to
determine the hazard classification of the dust
produced. Use an industrial dust extractor vacuum
of the appropriate, officially approved safety class
that is in compliance with your local dust hazard
control regulations.

WARNING: Always wear proper personal hearing
protection. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on
a stable surface where it will not cause a tripping or
falling hazard. Serious personal injury may result.

Residual Risks

In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot
during operation.
• Risk of personal injury due to prolonged use.