Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
S
w
i
t
c
h
i
n
g
o
f
f
S
w
i
t
c
h
i
n
g
o
f
f
For switching off the device release the circuit
closer/breaker or the switch button.
The cutting tool stops delayed after the machine is turned
off. Therefore wait until the cutting tool is stationary before
you restart the product.
R
e
m
o
v
i
n
g
t
h
e
b
a
t
t
e
R
e
m
o
v
i
n
g
t
h
e
b
a
t
t
e
To remove the battery press the battery release button (C).
W
o
r
k
i
n
W
o
r
k
i
n
You may not start to operate the machine until you have
read these operating instructions, observed all the in-
structions given and installed the machine as described!
Observe all safety instructions in any case.
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
h
h
e
e
d
d
g
g
e
e
Hold the hedge trimmer with both hands on a safe
distance from the body.
Scare animals off the hedge before starting to cut in order to
prevent them from being injured.
Due to its double sided knives the hedge trimmer can
be guided forward and backward or by oscillating move-
ments from one to another side.
The maximal diameter to cut depends on the wood's type,
age, moisture and hardness.
Best time for hedge trimming:
Leaved hedge:
⇒
⇒
Conifer hedge:
⇒
Quickly growing hedge:
At first cut the sides of the hedge and then the upper
edge.
Cut the hedge from the bottom up.
Cut the hedge in trapezium shape.
As a rule of thumb: 10 cm inclination per metre hedge
height.
For a 2 m high hedge having a width of 80 cm at its base
this means that its crown has a width of 40 cm, for example.
Stretch a guide over the complete length of the hedge when
you want to shorten the upper edge of the hedge evenly.
V
i
b
r
a
t
i
o
n
s
V
i
b
r
a
t
i
o
n
s
If persons who have blood circulation problems are too
often exposed to vibrations damages to the nervous system or
to blood vessels may occur.
You can reduce vibrations:
- by thick and warm working gloves,
- shorter working time (have longer breaks).
18
r
y
r
y
g
i
n
s
t
r
u
c
t
i
o
n
s
g
i
n
s
t
r
u
c
t
i
o
n
s
t
t
r
r
i
i
m
m
m
m
e
e
r
r
June and October
April and August
from May and then every 6
weeks
See a doctor if your fingers swell, you don't feel well or your
fingers become numb.
M
a
i
n
t
e
n
a
n
M
a
i
n
t
e
n
a
n
Before each maintenance and cleaning
work
− switch off device
− wait until the cutting device does not
longer move.
− remove the battery
− wear protective gloves.
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
M
a
i
n
t
e
n
a
n
c
e
M
a
i
n
t
e
n
a
n
c
e
The cutting tool will not come to a standstill immediately after
cut-off. Before starting any service work wait until all parts are
stationary.
To guarantee a long and reliable usage of the product carry out
the following maintainance works regularly.
Check the machine for obvious defects such as
− loose, hung out or damaged cutting tools
− worn or damaged components
− correct assembly and faultless covers and protective
devices.
Necessary repair works or maintainance have to be carried
out before using the power tool.
C
l
e
a
n
i
n
g
C
l
e
a
n
i
n
g
Before cleaning work on the charger:
Pull out mains plug.
Clean the machine and its accessories thouroughly after
each application so that the faultless function is kept.
Clean the case with a soft brush or a dry cloth.
Water, solvents and polishing agents shall not be
applied.
Make sure that the ventilation openings on the machine,
charger and battery are free (risk of overheating).
Clean the cutting device on a regular basis using a brush or
a cloth.
Never clean the knives with water
Risk of corrosion!
c
e
a
n
d
c
l
e
a
n
i
n
g
c
e
a
n
d
c
l
e
a
n
i
n
g
Werbung
Kapitel
Inhaltsverzeichnis
