Attaching The Grinding Wheel; Placing The Grinding Wheel In Position - Metabo W 750-100 Originalbetriebsanleitung

- Tighten the clamping screw (16) firmly. Make sure
that the guard is seated securely - you should not
be able to turn the safety guard (11).
WP 1100-115, WQ 1100-125, WEQ 1400-125:
See illustration D on page 2.
- Push and hold the lever (18). Place the safety
guard (11) in the position indicated.
- Release the lever and rotate the guard
until the lever latches.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is attached securely:
The lever must engage and you should not be able
to turn the safety guard.

7. Attaching the grinding wheel

Prior to any conversion work: pull the mains
plug out of the socket. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the cut-off
grinding guard before performing cut-off
grinding work (see Chapter 11. Accessories).
7.1 Locking the spindle
- Press in the spindle locking button (4) and
turn the spindle (3) by hand until the spindle
locking button engages.
7.2

Placing the grinding wheel in position

See illustration A on page 2.
- Fit the support flange (2) on the spindle. The
flange should not turn on the spindle when
properly attached.
Only W ... -100: Screw support flange with two-
hole spanner onto spindle so that the small collar
(with diameter 16 mm) is facing upwards.
- Place the grinding wheel on the support flange (2).
The grinding wheel must lay flat on the supporting
flange.
7.3 Securing/Releasing the "M-Quick"
clamping nut (depending on features)
Securing the "M-Quick" clamping nut (1):
Only for WQ1100-125; WEQ 1400-125.
Do not use the "M-Quick" clamping nut if the
accessory has a clamping shank thicker than
7,1 mm! In this case, use the 2-hole nut (12) with 2-
hole spanner (13).
- Lock the spindle (see chapter 7.1).
- Position the "M-Quick" clamping nut (1) on the
spindle (3) so that the 2 lugs engage in the 2
grooves on the spindle. See illustration on page 2.
- Tighten the "M-Quick"clamping nut by turning it
clockwise by hand.
Use only accessories that
are covered by at least 3.4
mm by the safety guard.
- Turn the grinding wheel firmly clockwise to tighten
the "M-Quick"clamping nut.
Releasing the "M-Quick" clamping nut (1):
The "M-Quick" clamping nut (1) must be
attached before the spindle locking button (4)
can hold the spindle!
- The machine continues to run after switching off.
- Press in the spindle locking button (4) just before
the grinding wheel stops. The "M-Quick"clamping
nut (1) is released.
7.4 Securing/Releasing the 2-hole nut
(depending on features)
Securing the 2-hole nut (12):
The 2 sides of the two-hole nut are different.
Screw the two-hole nut onto the spindle as follows:
See illustration B on page 2.
- X) For thin grinding discs:
The edge of the 2-hole nut (12) faces upwards so
that the thin grinding disc can be attached
securely.
Y) For thick grinding discs:
The edge of the two-hole nut (12) faces
downwards so that the two-hole nut can be
attached securely to the spindle.
Z) Only for W ... -100:
The collar of the two-hole nut faces downwards
and/or the flat surface faces upwards.
- Lock the spindle. Turn the two-hole nut (12)
clockwise using the two-hole spanner (13) to
secure.
Releasing the 2-hole nut:
- Lock the spindle (see chapter 7.1). Turn the two-
hole nut (12) anticlockwise using the two-hole
spanner (13) to unscrew.
7.5 Securing/releasing the (tool-free)
clamping nut
(depending on features)
Only tighten the (tool-free) clamping nut (14)
by hand!
For the machine to operate, the clip (15) must
always lie flat on the clamping nut (1).
To secure the (tool-free) clamping nut (14):
Do not use the clamping nut (tool-free) if the
accessory has a clamping shank thicker than
6 mm! In this case, use the 2-hole nut (12) with 2-
hole spanner (13).
- Lock the spindle (see chapter 7.1).
- Flip up the clip (15) on the clamping nut.
- Fit the clamping nut (14) on the spindle (3). See
illustration on page 2.
- Tighten the clamping nut on the clip (15)
manually in a clockwise direction.
- Flip down the clip (15) again .
Release the (tool-free) clamping nut (14):
- Lock the spindle (see chapter 7.1).
- Flip up the clip (15) on the clamping nut.
- Unscrew the clamping nut (14), turning it
anticlockwise manually .
ENGLISH en
17