Initial Operation; Attaching The Grinding Wheel - Metabo W 18 LT BL 11-125 Originalbetriebsanleitung

en ENGLISH

6. Initial Operation

6.1 Attaching the additional handle
Always work with the additional handle (19)
attached! Attach the additional handle on the
left or right of the machine and secure.
6.2 Attach the safety guard
For safety reasons, only use the guard
provided for the respective accessory! Using
an incorrect guard can lead to loss of control and
serious injuries. See also chapter 11. Accessories!
See illustration H on page 2.
- Push and hold the lever (23). Place the safety
guard (20) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Push the lever and turn the safety guard until the
closed section is facing the operator.
- Make sure that the guard is attached securely:
The lever must engage and you should not be able
to turn the safety guard.
6.3 Dust filter
See illustration B on page 2.
Always fit the dust filter (12) if the surroundings
are heavily polluted.
The machine heats up faster when the dust
filter (12) is fitted. It is protected by the
electronics system from overheating (see Section
10.).
To fit:
Fit the dust filter (12) as shown.
Removal:
Holding the dust filter (12) at the edges, raise it
slightly and then pull it downwards and remove.
6.4 Rotating battery pack
See illustration D on page 2.
The rear section of the machine can be rotated 270°
in 3 stages, thus allowing the machine's shape to be
adapted to the working conditions. Only operate the
machine when it is in an engaged position.
First press the locking button (18), rotate the rear
part of the machine while keeping it pressed.
Release the button while rotating the machine. The
locking mechanism must engage with an audible
"click".
6.5 Battery pack
Charge the battery pack (9) before use.
Recharge the battery pack if performance
diminishes.
Instructions on charging the battery pack can be
found in the operating instructions of the Metabo
charger.
18
Use only accessories that
are covered by at least 3.4
mm by the safety guard.
(Disassemble in reverse
order.)
In case of Li-Ion battery packs with capacity and
signal display (16) (equipment-specific):
- Press the button (15), the LEDs indicate the
charge level.
- The battery pack is almost empty and must be
recharged if one LED is flashing.
6.6 Removing and inserting the battery pack
Hold the machine when removing and
inserting the battery pack so that the on/off
switch cannot be unintentionally pressed.
Removing:
Press the battery pack release (8) button and
remove the battery pack (9).
Inserting:
Slide in the battery pack (9) until it engages.

7. Attaching the grinding wheel

Prior to any conversion work: remove battery
pack from machine. The machine must be
switched off and the spindle at a standstill.
For reasons of safety, attach the cut-off
grinding guard before performing cut-off
grinding work (see Chapter 11. Accessories).
7.1 Locking the spindle
- Press in the spindle locking button (4) and turn the
spindle (3) by hand until the spindle locking button
engages.
7.2 Placing the grinding wheel in position
See illustration A on page 2.
- Fit the support flange (2) on the spindle. The
flange should not turn on the spindle when
properly attached.
7.3 Securing/Releasing the "Quick"
clamping nut (depending on features)
Securing the "Quick" clamping nut (1):
Only attach the "Quick" clamping nut (1) to
tools with "Metabo Quick System". These
tools can be identified by the red spindle lock button
(4) with "M-Quick" logo
Do not use the "Quick" clamping nut if the
accessory has a clamping shank thicker than
7.1 mm! In this case, use the 2-hole nut (21) with 2-
hole spanner (22).
- Lock the spindle (see chapter 7.1).
- Position the "Quick" clamping nut (1) on the
spindle (3) so that the 2 lugs engage in the 2
grooves on the spindle. See illustration on page 2.
- Tighten the "Quick"clamping nut by turning
clockwise by hand.
- Turn the grinding wheel firmly clockwise to tighten
the "Quick"clamping nut.
Releasing the clamping nut (1):
Only when the "Quick" clamping nut (1) is
attached must the spindle be stopped using
the red M-Quick spindle locking button (4)!