Combinations Of Cutting Attachments And Deflectors; Spare Parts And Accessories - Stihl FSA 86 R Gebrauchsanleitung

21 Combinations of Cutting Attachments and Deflectors

®
– Bluetooth radio interface (only for batteries
with ):
– Data connection: Bluetooth
mobile appliance must be compatible with
®
Bluetooth Low Energy 5.0 and support
Generic Access Profile (GAP).
– Frequency band: ISM band 2.4 GHz
– Maximum RF power transmitted: 1 mW
– Signal range: approx. 10 m. The signal
strength depends on the ambient conditions
and the mobile terminal. Signal range can
vary greatly depending on local conditions,
including the receiver. The range may be
perceptibly reduced inside enclosed rooms
and through metal barriers (such as walls,
shelves or cases).
– Mobile appliance operating system require‐
ments: Android or iOS (current version or
higher)
20.3 Sound Values and Vibration
Values
K-value (uncertainty) for sound pressure levels is
2 dB(A). K-value for sound power levels is 2
dB(A). K-value for vibration level is 2 m/s².
STIHL recommends wearing ear defenders.
Using with a mowing head except PolyCut 6-2
– Sound pressure level L
to EN 50636-2-91: 77 dB(A)
– Sound power level L
EN 50636-2-91: 91 dB(A)
– Vibration level a measured as specified in
hv
EN 50636-2-91
– Control handle: 2.0 m/s².
– Loop handle: 3.7 m/s².
Using with a mowing head PolyCut 6-2
– Sound pressure level L
fied in EN 50636‑2‑91: 81 dB(A)
– Sound power level L
in EN 50636-2-91: 94 dB(A)
– Vibration level a measured as specified in
hv
EN 50636-2-91
– Control handle: 2.0 m/s².
– Loop handle: 3.7 m/s².
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
0458-833-9821-C
®
5.1. The
measured according
pA
measured according to
wA
measured as speci‐
pA
measured as specified
wA
mated. The times when the power tool is
switched off and the times when it is switched on
but running under no load can be taken into
account in the estimate.
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
20.4 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
21 Combinations of Cutting
Attachments and Deflec‐
tors
21.1 STIHL FSA 86 R Brushcutters
The following mowing heads may be mounted
together with the guard for mowing heads:
– STIHL AutoCut C 6-2 mowing head:
– with round, low-noise mowing line with a
diameter of 2.0 mm or 2.4 mm
– PolyCut 6-2 mowing head
– with blades
– with round, low-noise mowing line with a
diameter of 2.0 mm or 2.4 mm
– DuroCut 5-2 mowing head:
– with blades
– with round, low-noise mowing line with a
diameter of 1.6 mm, 2.0 mm or 2.4 mm
22 Spare Parts and Accesso‐
ries
22.1

Spare parts and accessories

These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
STIHL recommends the use of original STIHL
spare parts and accessories.
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
Original STIHL spare parts and original STIHL
accessories are available from STIHL dealers.
English
33