Inhaltsverzeichnis - VHF S5 Originalbetriebsanleitung

Contents
Contents
1 Welcome
1.1 About this document
1.2 Used symbols
1.3 Structure of safety notes
2 General safety instructions
3 Operating regulations
3.0.1 Intended use
3.0.2 Controlling the machine through software
3.0.3 Maintenance and cleaning
3.0.4 Spindle
3.0.5 Unattended operation
3.0.6 Transportation and storage
4 Machine overview
4.1 Front side of the machine
4.2 Connection panel
4.3 Working chamber door
4.4 Working chamber
4.5 Blank magazine
4.6 CAM computer
4.7 Anti-soiling concept
4.8 Sound emission
4.9 Location of the identification plate & serial number
4.10 Axes
4.11 Technical data
5 Installing the machine
5.1 Checking the scope of delivery
5.2 Choosing the installation site
5.3 Machine installation (schema)
5.4 Establishing the electric connection
5.5 Removing the transport lock
5.6 Installing the pneumatics
5.6.1 Overview compressed air regulator
5.6.2 Installing the pneumatic hose
5.6.3 Adjusting the air pressure with the compressed air
regulator
5.7 Installing the air extraction system
5.7.1 Requirements for the suction unit
5.7.2 Installing the suction unit
5.7.3 Connecting the suction hose with the optional
hose connection
5.7.4 Installing the switching unit
5.8 Connecting the CAM computer
6 Operation: Preparing jobs
6.1 Starting the machine
6.2 Starting the machine with a tool in the collet chuck
5
5
5
5
6
9
9
9
9
9
9
10
11
11
11
12
12
13
13
13
14
14
14
15
17
17
18
19
20
20
21
22
22
23
24
24
24
24
25
25
26
26
26
Original Operating Instructions: S5
Version: 12/15/2021
6.3 Switching off the machine
6.4 Mounting & removing blanks
6.4.1 Mounting blocks to the block holder
6.4.2 Using an optional abutment holder
6.4.3 Operating the blank changer
6.4.4 Change position of the blank magazine
6.4.5 Mounting discs & block holders to the blank
magazine
6.5 Managing tools
6.5.1 Inserting and exchanging tools
6.6 Deactivating and activating the ionizer
6.7 Mounting and removing the ionizer cover
6.8 Preparing the machine for wet machining
7 Operation: Executing jobs
7.1 Starting jobs
7.2 Aborting machining
7.3 Job interruptions and job abortions
7.3.1 How to proceed in case of a job interruption
7.3.2 How to proceed in case of a machine malfunction 39
7.3.3 How to proceed in case of a tool breakage
7.3.4 How to proceed in case of a power failure
7.4 Emergency opening of the working chamber door
7.5 Manually resetting the blank changer to default pos-
ition
8 Maintenance and do-it-yourself
8.1 Basic maintenance
8.2 Maintenance section
8.3 Preventive maintenance
8.4 Where to get service?
8.5 Definition of wear parts
8.6 Cleaning the working chamber
8.7 Cleaning the blank magazine
8.8 Cleaning the collet chuck
8.9 Checking the compressed air regulator
8.9.1 Checking the water separator for condensate
8.9.2 Exchanging / cleaning the contaminated filter cart-
ridge
8.10 Cleaning the housing
8.11 Exchanging the main fuse
8.12 Calibrating the axes
8.13 Replacing the tool magazine inserts
8.14 Updating the software and firmware
8.14.1 Updating the manufacturing software
8.14.2 Updating the firmware of the machine
8.15 Maintenance table
9 Disposal
9.1 Disposing of the cooling liquid
9.2 Disposing of the machine
EN 3
27
27
28
29
29
30
30
33
33
35
35
36
38
38
38
39
39
39
40
41
42
43
43
43
43
43
43
44
45
46
48
48
48
49
50
50
51
52
52
52
53
55
55
55