Unpacking And Assembly; Fitting The Steering Wheel - Stiga NJ 92-Serie Gebrauchsanweisung

labels are to be considered an integral part of
the machine. If a label should fall off or become
illegible, contact your Retailer to replace it. Their
meaning is explained below.
31. Warning: Read the instructions before op-
erating the machine.
32. Warning: Disconnect the key and read the
instructions before carrying out any mainte-
nance or repair work.
33. Danger! Ejected objects: Do not operate
without either the rear discharge guard or
the grass catcher being in place.
34. Danger! Ejected objects: Keep bystand-
ers away.
35. Danger! Machine rollover: Do not use this
machine on slopes greater than 10°.
36. Danger! Dismemberment: Make sure that
children stay clear of the machine all the
time when engine is running.
37. Danger of cutting yourself. Cutting
means in motion. Do not put hands or feet
near or under the opening of the cutting
means housing.
38. Warning! Keep away from hot surfaces.
39. Do not climb onto the machine putting your
feet on the cutting-means assembly.
2.4 REGULATIONS FOR TOWING
A kit for towing a small trailer is available on re-
quest. This attachment must be fitted following
the instructions provided.
41. W hen using the towing kit, do not exceed
the recommended loads stated on the label
and follow the safety instructions.
NOTE The images corresponding to the texts
in chapters 3 et seq., can be found on pages iii et
seq. of this manual.

3. UNPACKING AND ASSEMBLY

For storage and transport purposes, some com-
ponents of the machine are not installed in the
factory and have to be assembled after unpack-
ing. Follow the instructions below.
IMPORTANT The machine is supplied without
engine oil or fuel. Before starting up the engine,
fill with oil and fuel following the instructions given
in the engine manual.
WARNING! Unpacking and completing
the assembly should be done on a flat and
stable surface, with enough space for mov-
ing the machine and its packaging, always
making use of suitable equipment.
3.1 UNPACKING
When unpacking the machine, take care to
gather all individual parts and fittings, and do
not damage the cutting-means assembly when
taking the machine off the pallet.
The packaging contains:
– t he machine;
– t he steering wheel;
– t he seat;
– t he front bumper (if provided);
– t he battery;
– t he grass catcher (with instructions);
– a n envelope containing:
– t he instruction manuals and documents,
– n uts and bolts including a pin for locking the
steering wheel,
– 2 ignition keys and a spare 10A fuse.
NOTE To avoid damaging the cutting-means
assembly when getting the machine down from
the pallet, take it to the maximum height and be
very careful.
Hydrostatic transmission:
– T o make it easier to get the machine off
the pallet and to move it, the rear drive dis-
engage lever should be put in position «B»
(see 4.33).
Disposal of the packaging should be done in ac-
cordance with the local regulations in force.

3.2 FITTING THE STEERING WHEEL

• Steering wheel Type "I" (Fig. 3.1)
Put the machine on a flat surface and straighten
the front wheels.
Fit the steering wheel (1) onto the protruding
shaft (2) with the spokes directed towards the
seat.
Line up the hole on the steering wheel hub with
the hole on the shaft and insert the pin (3) us-
ing a hammer. Make sure the end comes right
through to the opposite side.
NOTE To avoid damaging the steering wheel,
use a punch or a screw-driver of the same size
as the pin when hammering it in the last part.
• Steering wheel Type "Il" (Fig. 3.2)
Put the machine on a flat surface and straighten
the front wheels.
Fit the steering wheel (1) onto the protruding
shaft (2), and rotate it so the spokes point in the
6