Lawn Mower Safety Warnings; Intended Use; Residual Risk - Ryobi RLM15E36H Originalanleitung

authorised service centre for professional repair.
A power spike causes voltage fluctuations and may
affect other electrical products in the same power
line. Connect the product to a power supply with an
to minimize voltage fluctuations. Contact your electric
power supplier for further clarification.

LAWN MOWER SAFETY WARNINGS

Before using, always visually inspect to ensure blades,
blade bolts, and cutter assembly are not worn or
damaged.
Replace worn or damaged blades and bolts in sets to
preserve balance.
The blade on the product is very sharp. Use extreme
caution and wear heavy duty gloves when fitting,
replacing, cleaning or checking bolt security.
Return to an authorised service centre to replace
damaged or unreadable labels.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
Check the grass box frequently for wear, holes or
deterioration.
Replace worn or damaged parts before operating the
product.
The mower must be started with the user behind the
handlebars in the operator safety zone. Never start the
product if:
All four wheels are not on the ground
The grass discharge chute is exposed without being
protected by either the mulching plug and grass
discharge chute cover or the grass box and grass
discharge chute cover.
Hands and feet of all persons are not clear of the
cutting enclosure.
Never operate the product if the on/off switch on the
handlebar does not properly start and stop the product.
Never attempt to lock the on/off switches in the On
position, this is extremely dangerous.
Do not force the product. It will do the job better and
safer at the speed for which it was designed.
Stop the blade when crossing gravel surfaces.
Do not pull the product backward unless absolutely
necessary. If you must back the product away from a
tripping or pulling the product over your feet.
Stop the motor and allow the blade to stop if the
product has to be tilted for transportation when crossing
surfaces other than grass, and when transporting the
product to and from the area to be mowed.
Never use the product with defective guards or shields,
or grass boxes, in place.
Do not tilt the product when switching on the motor or
whilst the motor is running. This exposes the blade and
increases the probability of objects being thrown.
Switch on the motor carefully according to instructions
and keep hands and feet away from cutting area. Do not
put hands or feet near or under rotating parts Keep clear
of the discharge opening at all times. Do not start the
product when standing in front of the discharge opening.
2 | English
Never pick up or carry the product while it is running.
Stop the mower motor and disconnect from the power
supply, make sure that all moving parts have come to a
complete stop for the below cases:
whenever you leave the product unattended
(including disposal of grass clippings).
before cleaning a blockage or unclogging discharge
chute
before checking, cleaning or working on the product
after striking a foreign object; inspect the product
for damage and make repairs as necessary before
restarting and operating the product.
before removing the grass box or opening the grass
discharge chute cover.
If the product starts to vibrate abnormally (check
immediately)
– inspect for damage, particularly the blades
– replace or repair any damaged parts
– check for and tighten any loose parts
Avoid holes, ruts, bumps, rocks, property stakes, or
other hidden objects. Uneven terrain could cause a slip
and fall accident.
OVERLOAD PROTECTION DEVICE
The product has an overload protection device. When
overloading is detected, the product will automatically
switch off. If the overload protector is actuated, the motor
must be allowed to cool down for 5 to 10 minutes.
Turn off the power and remove the plug from the supply.
The blades are sharp, wear heavy duty gloves before
touching. Make sure the blade can rotate freely and is not
jammed or tight.
When the motor is cool, connect the plug to the power
supply, turn the power on. Press the Start button and then
the On-off button to start the product. If the product will still
not start, return it to an authorised service centre for repair.

INTENDED USE

The product is only intended for use outdoors.
The product is designed for domestic lawn mowing. The
cutting blade should rotate approximately parallel to the
ground over which it is being wheeled. All four wheels should
touch the ground while mowing. It is a pedestrian controlled
walk behind mower designed to be pushed by hand.
The product should never be operated with the wheels off
the ground; it should not be pulled or ridden on. It should not
be used to cut anything other than domestic grass lawns.

RESIDUAL RISK

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Injury caused by vibration. Always use the right tool for
the job, use designated handles and restrict working
time and exposure.
Exposure to noise can cause hearing injury. Wear ear
protection and limit exposure.
Contact with blades
Injury from thrown objects