TermaTech TT30G Montage- Und Bedienungsanleitung Seite 26

MAINTENANCE – always use original parts
Maintenance and cleaning of the stove should only be performed when the stove is cold. The daily
maintenance is limited, but once a year the stove should get thorough maintenance. The combu-
stion chamber should be cleaned for ashes and soot and the door hinges and the closing mecha-
nism should be lubricated with copper grease.
The surface is maintained by brushing it with a soft, long-haired brush or by using the vacuum
cleaner with a brush.
The stove can also be dusted with a duster. Always remember: only when the stove is cold.
Jointings can look okay, but they collapse under the heat and thereby lose the ability to keep the
stove sealed. Jointings should be changed as needed as it is important to good combustion and a
clean window that the stove is sealed.
The insulation plates in the combustion chamber that are broken or worn can easily be chan-
ged as they are loosely fixed. The material used is called Vermiculite and is a porous, but very
suitable insulation material. It has no effect on the stove's efficiency that the insulation cracks.
However, it should be changed when the wear surpasses half of the original thickness. See dra-
wing 5+6 (page 61)
Painting the stove with Senotherm-spray can cover spots or small scratches from kettles and
such. Larger damages needs to be ground with fine steel wool, vacuumed and then sprayed.
The can has to be shaken vigorously and then sprayed on at a distance of 15-20 cm. It is very
important that the stove is not in use and completely cold before you use the spray due to the fire
hazard. In order to keep the stove's varnished surfaces looking nice for years to come you should
try to avoid touching the varnished surfaces when the stove is hot. Make sure to have sufficient
ventilation when using spray paint.
Glass normally does not need any maintenance apart from cleaning. This is most easily done by
using TermaTech's glass cleaner. Remember only to use glass cleaner when the stove is cold. The
TT30G, which is furnished with side glass/windows, has no air-wash system on its side glass/win-
dows. Hence they can become sooty more often, and possibly will require more frequent cleaning.
Original parts which need to be changed due to wear can be found at your dealer. Because of fit
etc. only original parts from TermaTech should be used.
Right to claim compensation for defective product is under current law.
When stating deviations the use of the product must be suspended immediately and the dealer
must be contacted.
Chimney/Flues must be swept on regular occasions, as per manufacturers recommendations.
5 YEAR WARRANTY* / RIGHT TO INVOKE LACK OF CONFORMITY
If defects/faults are ascertained, use of the wood burner must be stopped immediately and the
dealer contacted.
*5 Year warranty
Provided that there has been normal operation of the wood burner, TermaTech offers a 5 year
warranty on material and manufacturing faults on the load-bearing frame, exclusive of the com-
bustion chamber.
Combustion chamber: The following parts are not covered by the warranty: The combustion
chamber, Cast iron parts (bottom, door and grate), Insulation material (vermiculite plates),
Smoke deflector plates, Glass, gaskets as well as the closing mechanism/handle.
Exterior parts: The following parts are not covered by the warranty: Varnished plates/surfaces,
stone facings, glazed tiles, concrete and glass as well as the closing mechanism/ handle
The warranty does not cover faults which are due to:
• the user/mounting guide not being followed
• the mounting being carried out incorrectly
• overheating/deterioration of the materials, caused by the use of, for example, the incorrect
type of fuel, petroleum coke or too much fuel
• the product has been connected to a chimney with poor drawing qualities, for example, chim-
neys that are too short or are leaking
• the product being positioned or has been positioned/kept in unheated or damp surroundings
• the product being in bad repair or not maintained in accordance with the instructions
• normal wear and tear of wearing parts/expendable items as well as the varnish
• similar circumstances which are not due to material or manufacturing faults
26