Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
T
a
b
e l
1
B
u
n r
r e
R
a
p
d i
C
S
e
m
- i
a r
p
d i
B
A
u
i x
a i l
y r
A
r T
p i
e l
r
n i
g
D
S
u
p
p
y l
p
e r
s s
u
e r
TECHNICAL SPECIFICATIONS
ENERGY LABEL
Directive 2002/40/EC on the label of electric ovens
Norm EN 50304
Energy consumption for Natural convection
heating mode:
Convection ( only for mod. KP 688 MS)
Declared energy consumption for Forced convection Class
heating mode:
Fan assisted
THE APPLIANCE MUST BE EARTHED
The appliance is designed to work with alternating current
at the supply voltage and frequency indicated on the rating
plate (situated on the rear part of the appliance and on the
last page of the instruction manual). Make sure that the
local supply voltage corresponds to the voltage indicated
on the rating plate.
Connecting the supply cable to the mains electricity
supply
For models supplied without a plug, fit a standard plug,
suitable for the load indicated on the rating plate, onto the
cable and connect it to a suitable socket.
To connect directly to the mains supply, an omnipolar circuit-
breaker with a contact separation of at least 3 mm suitable
for the load and complying with current standards and
regulations must be fitted between the appliance and the
mains supply outlet.
The yellow-green earth wire must not be interrupted by
the switch.
The supply cable must be in such a position so that no
BURNER AND NOZZLE SPECIFICATIONS
D
a i
m
t e
r e
T
h
r e
m
l a
p
o
w
(
m
m
)
k
W
(
H
s .
) * .
N
o
m
i
. n
R
e
d
1
0
0
3
0 .
0
0
7 .
7
5
1
6 .
5
0
4 .
5
5
1
0 .
0
0
3 .
1
3
0
3
2 .
5
1
3 .
ELECTRICAL CONNECTION
L
q i
u
d i
r e
B
y
p -
a
s s
N
o
z z
e l
1
1 /
0
0
1
1 /
0
0
(
m
m
)
(
m
m
)
u
. c
4
0
8
6
3
0
6
4
2
7
5
0
5
7
9
1
* At 15°C and 1013 mbar-dry gas
Propane G31
Butane G30
Methane G20
This appliance conforms to the following European Economic
Community directives:
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and
subsequent modifications;
- 90/396/EEC of 29/06/90 (Gas) and subsequent modifications;
- 93/68/EEC of 22/07/93 and subsequent modifications.
part of it can reach a temperature of 50 °C above room
temperature.
All appliances should be connected seperately.
Do not use reducers, adapters or shunts as they could
cause heating or burning.
Before connecting to the power supply, make sure that:
• the limiter valve and the domestic system can withstand
the load from the appliance (see rating plate);
• the supply system is efficiently earthed according to
standards and laws in force;
• the socket or omnipolar circuit-breaker are easily
accessible when the appliance is installed.
FAILURE TO OBSERVE THE ACCIDENT-PREVENTION
REGULATIONS RELIEVES THE MANUFACTURER OF ALL
LIABILITY.
Replacing the cable
Use a rubber cable of the type H05VV-F with a cross section
of 3 x 1,5 mm² .
The yellow-green earth wire must be 2 ÷ 3 cm longer than
the other wires.
9
g
a
s
N
t a
F
o l
w
*
N
o
z z
g
h /
1
1 /
0
0
(
m
m
G
3
0
G
3
1
2
1
8
2
1
4
1
1
6
1
2
0
1
1
8
9
6
7
3
7
1
7
1
2
3
6
2
3
2
1
2
4
3
0
3
7
H.s. = 50,37 MJ/kg
H.s. = 49,47 MJ/kg
H.s. = 37,78 MJ/m 3
r u
l a
g
a
s
e l
F
o l
w
*
l
h /
)
G
2
0
2
8
6
1
5
7
9
5
3
0
9
2
0
Werbung
Inhaltsverzeichnis
