Vitek VT-3406 W Betriebsanweisung Seite 4

ENGLISH
Check the power cord and plug periodically.
Do not use the unit if the motor unit body, the
power plug or the power cord have damages.
Do not disassemble and repair the unit by
yourself. If you find any damages, unplug the
unit and apply to an authorized service center.
To avoid damages, transport the unit in origi-
nal package only.
Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE USING THE UNIT
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature before
switching on.
– Unpack the unit completely and remove any
stickers that can prevent unit operation.
– Check the unit for damages; do not use it in
case of damages.
– Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
– Before using the unit, wash all removable
parts in warm water with a neutral detergent:
the blender attachment (1), the whisk (7), the
measuring cup (8) and the cookie attachment
(10-14).
– Wipe the motor unit (2), whisk gear (6) and
cookie attachment gear (9) with a soft slightly
damp cloth and then wipe them dry.
Attention!
Do not immerse the motor unit (2), the gears
(6, 9), the power cord and the power plug
into water or any other liquids.
Do not put the attachments and bowls in a
dishwashing machine.
Continuous operation time
The continuous operation time while working with
the blender attachment and the whisk should
not exceed 1 minute, and the break between
operations should be no less than 2 minutes. The
continuous operation time while using the cookie
attachment is no longer than 5 minutes; make at
least 5 minute breaks between operation cycles.
USING THE BLENDER ATTACHMENT
WARNING: Before installing the attachment,
VT-3406.indd 4
make sure that the power plug is not inserted
into the mains socket.
– Attach the blender attachment (1) to the
motor unit (2), matching the mark
mark on the attachment and turn it clock-
wise till bumping. The mark
the mark in the fixed position.
– Insert the power plug into the mains socket.
– Immerse the blender attachment (1) into the
bowl with products that you want to chop or
mix. You can use the measuring cup (8) as
a bowl.
– To switch the unit on, press and hold the «I»
button (3). Use this mode for mixing liquid
products.
– If you press and hold the «II» button (5), the
unit will operate at maximum rotation speed.
Use this mode for combined processing of liq-
uid and hard products.
Note:
Products should be put into the bowl before
the unit is switched on. The amount of
processed products should not exceed 2/3
of the capacity of the bowl in which they are
processed.
Before starting chopping/mixing,
recommend to peel fruit, remove inedible
parts, such as stones, and cut fruit into 2х2
cm cubes.
– After you finish using the unit, unplug it and
remove the blender attachment (1) by turn-
ing it counterclockwise so that the mark
opposite the mark
Attention!
Do not remove the blender attachment (1)
during operation.
To avoid damaging the blades, do not
process too hard products such as cereals,
rice, spices, coffee beans, cheese, frozen
food, and ice.
If the products are difficult to process, add
some water.
USING THE WHISK
Use the whisk (7) only to make cream, biscuit
dough or mixing ready desserts.
WARNING: Before assembling, make sure
that the power plug is not inserted into the
mains socket.
– Insert the whisk (7) into the gear (6).
– Install the gear (6) with the whisk on the
motor unit (2) so that the mark
4
with the
should match
we
is
.
is opposite
10.12.2013 12:15:22