Using The Appliance - Philips AVENT SCD535 Benutzerhandbuch

4.2 Parent unit
4.2.1 Operation on rechargeable battery
pack
The parent unit comes with a rechargeable Li-ion
1000mAh battery pack.
Charge the parent unit before you use it for the
first time or when the parent unit indicates that
the battery is low (the empty battery symbol
flashes on the display and the parent unit beeps).
The parent unit starts indicating that the battery
pack is low 30 minutes before the battery pack is
completely empty.
Note:
D
If the rechargeable battery pack is completely
empty, the parent unit automatically switches off
and loses contact with the baby unit.
Remove the lid of the compartment for the
1
rechargeable battery pack (Fig. 6).
Insert the rechargeable battery pack (Fig. 7).
2
Reattach the lid (Fig. 8).
3
Insert the small appliance plug into the
4
charger, put the adapter in a wall socket and
place the parent unit in the charger (Fig. 9).
• The charging light on the charger goes on. ging light on the charger goes on. ging light on the charger goes on.
• The display shows a charging battery symbol ws a charging battery symbol ws a charging battery symbol
to indicate that the parent unit is charging. to indicate that the parent unit is charging. to indicate that the parent unit is charging.
Leave the parent unit in the charger until the ve the parent unit in the charger until the ve the parent unit in the charger until the
5
battery pack is fully charged. fully charged. fully charged.
• During charging, the charging light on the ing charging, the charging light on the ing charging, the charging light on the
charger lights up continuously. charger lights up continuously. charger lights up continuously.
• When the When the batter When the battery pack is fully charged, battery pack is fully charged,
the display of the parent unit shows a full
battery symbol T.
•
When you charge the parent unit for
the first time or after a long period of
disuse, switch it off and let it charge
continuously for at least 10 hours.
•
Charging normally takes 4 hours, but
it takes longer when the parent unit is
switched on while charging. To keep the
charging time as short as possible, switch
off the parent unit during charging.
• When the battery pack is fully charged,
the parent unit can be used cordlessly for
up to 24 hours.
8
All manuals and user guides at all-guides.com
wall socket and wall socket and
9). 9).
y pack is fully charged,
Note:
D
When the parent unit is charged for the first
time, the operating time is less than 24 hours. The
battery pack only reaches its full capacity after you
have charged and discharged it four times.
Note:
D
When the parent unit is not in the charger, the
battery pack gradually discharges, even when the
parent unit is switched off.

5 Using the appliance

Place the parent unit and the baby unit in the nt unit and the baby unit in the nt unit and the baby unit in the
1
same room to test the connection same room to test the connection same room to test the connection (Fig. 10).
Make sure the baby unit is at least 1 metre/3 Make sure the baby unit is at least 1 metre/3 Make sure the baby unit is at least 1 metre/3
feet away from the parent unit. feet away from the parent unit. feet away from the parent unit.
Press Press Press and hold the on/off button 3on the and hold the on/off button and hold the on/off button
2
baby unit until the green power-on light goes baby unit until the green power-on light goes baby unit until the green power-on light goes
on. on. (Fig. 11) on. (Fig. (Fig.
Note:
D D D
The power-on light always lights up green,
even when there is no connection with the
parent unit.
• The nightlight lights up briefly and then
fades out again.
• The display lights up and the battery symbol
appears on the display (Fig. 12).
• After 2 seconds the temperature and
humidity values are shown on the
display (Fig. 13).
Press and hold the on/off button 3on the
3
parent unit until the sound level lights light up
briefly. (Fig. 14)
• The display goes on and the battery symbol
appears on the display (Fig. 15).
• The LINK light flashes red and the message
'Searching' appears on the display (Fig. 16).
The LINK light on the parent unit
•
turns green and lights up continuously when
a connection has been established between
the baby unit and parent unit. The message
'Linked' appears on the display (Fig. 17).