Philips AVENT SCD535 Benutzerhandbuch Seite 14

7.8 Temperature alert on/off
Note:
D
You can only switch the temperature alert on and
off in the menu of the parent unit.
Note:
D
If the temperature alert is activated too often,
reduce the set minimum temperature and/or
increase the set maximum temperature (see
'Setting room temperature range').
If the temperature alert is switched on, the parent
unit beeps if the actual room temperature exceeds
the set maximum temperature or drops below the
set minimum temperature. In addition, the backlight
of the parent unit display goes on, the temperature
alert symbol ( t) flashes and 'High' or 'Low' appears
on the display. If no minimum and maximum
temperatures have been set, the temperature
alert is given when the room temperature drops
below 14°C or rises above 35°C.
Select 'Temperature' with the + and - buttons.
1
Press the OK button to confirm.
2
Select 'Alert' with the + and - buttons.
3
Press the OK button to confirm.
4
If the alert is off, the display shows 'On?'. Press
5
the OK button to switch on the alert. If the the OK button to switch on the alert. If the the OK button to switch on the alert. If the
alert is on, the display shows 'Off?'. Press the alert is on, the display shows 'Off?'. Press the alert is on, the display shows 'Off?'. Press the
OK button to switch off the alert. OK button to switch off the alert. OK button to switch off the alert.
7.9 Vibration alert on/off Vibration aler Vibration alert on/off
Note:
D
You can only switch the vibration alert on and off
in the menu of the parent unit.
If the vibration alert is switched on, the parent
unit vibrates as soon as the fourth sound level
light lights up while the volume is switched off.
Select 'Alert settings' with the + and - buttons.
1
Press the OK button to confirm.
2
Select 'Vibration' with the + and - buttons.
3
Press the OK button to confirm.
4
If the vibration alert is off, the display shows
5
'On?'. Press the OK button to switch on the
vibration alert. If the vibration alert is on, the
display shows 'Off?'. Press the OK button to
switch off the vibration alert.
14
All manuals and user guides at all-guides.com
'On?'. 'On?'. Press 'On?'. 'On?'. Press 'On?'. 'On?'. Press Press
t on/off
7.10 Setting display language
Select 'Settings' with the + and - buttons.
1
Press the OK button to confirm.
2
Select 'Language' with the + and - buttons.
3
Press the OK button to confirm.
4
Select the desired language with the + and -
5
buttons.
Press the OK button to confirm.
6
7.11 Setting temperature scale
Note:
D
You can only set the temperature scale in the
menu of the parent unit.
You can set the temperature scale either to You can set the temperature scale either to You can set the temperature scale either to
Celsius (C) or Fahrenheit (F). Celsius (C) or Fahrenheit (F). Celsius (C) or Fahrenheit (F).
Select 'Settings' with the + and - buttons. 'Settings' with the + and - buttons. 'Settings' with the + and - buttons.
1
Press the OK b Press the OK Press the OK button to confirm. button to confirm. utton to confirm.
2
Select 'Temp scale' with the + and - buttons. 'T 'Temp scale' 'Temp scale' 'T 'Temp scale' 'T emp scale'
3
Press the OK b Press the OK button to confirm. Press the OK b
4
Select 'Celsius' or 'Fahrenheit' with the + and - Select Select 'Celsius' or 'Fahrenheit' with the + and - 'Celsius' or 'Fahrenheit' with the + and -
5
buttons. buttons. buttons.
7.12 7.12 7.12 Reset function
This function in the menu of This function in the menu of the parent unit This function in the menu of
allows you to reset both the parent unit and the
baby unit to the default settings at the same time.
You can use this function if problems occur that
you cannot solve by following the suggestions
in chapter 'Frequently asked questions'.
Select 'Settings' with the + and - buttons.
1
Press the OK button to confirm.
2
Select 'Reset' with the + and - buttons.
3
Press the OK button to confirm.
4
• The message 'Confirm?' appears on the
display of the parent unit.
Press the OK button to confirm.
5
• The parent unit switches off and then
switches on again.
• The units have now both been reset to the
default factory settings.