Technical Specifications - STEINEL US 360 COM1 Handbuch

Technical Specifications

Dimensions (W x H x D): 120 x 120 x 68 mm DualTech
120 x 120 x 73 mm Single US
120 x 120 x 68 mm US 360
120 x 120 x 73 mm Dual US
Power supply: 230 – 240 V, 50 Hz / 60 Hz
Capacity, switching output 1: Relay, 230 V
(COM 1/COM 2) 2000 W max. resistive load (cos φ = 1)
1000 VA max. (cos φ = 0.5)
Electronic ballasts: Max. ON current 800 A/200 μs
(COM 1/COM 1 AP/COM 2/DIM) 30 x (1 x 18 W), 25 x (2 x 18 W)
25 x (1 x 36 W), 15 x (2 x 36 W)
20 x (1 x 58 W), 10 x (2 x 58 W)
Pay attention to specific ON currents of electronic ballasts!
A relay or contactor must be provided on line side for
higher switching capacities
Capacity, switching output 2: Presence
(COM 2 only) 230 W/230 V
1A max. (cos φ = 1) for HVAC (heating/ventilation/air-conditioning)
US 360/DualTech
Detection ranges:
(Detection Tangential/presence (m): Ø 6 m max. (28 m
at 2.5 m / mounting Ø 2 m min. (12 m
height 2.5 m) Radial: Reach up to Ø 10 m
Light-level setting: 10 – 1000 lux, ∞ / daylight /
DIM 100 – 1000 lux control threshold
Switching output 1:
30 sec. – 30 min., pulse mode (approx. 2 sec.),
Time setting IQ mode (automatic adjustment to the usage profile)
Switching output 2: COM2 only, for HVAC
Time setting 0 sec. – 10 min. switch-ON delay
1 min. – 2 hrs. stay-ON time
Automatic room surveillance
DIM: 30 sec. – 30 min.,
Time setting IQ mode (automatic adjustment to the usage profile)
Control output: 1 – 10 V / 50 electronic ballasts max., 100 mA max.
Mounting height: 2.5 m – 3.5 m
(mounted to ceiling)
Point of installation: Indoors
Sensor technology:
DualTech PIR (Passive Infrared), single pyro, 11 detection levels,
520 switching zones. Ultrasonic 40 kHz
US 360 / Single US / DualTech Ultrasonic 40 kHz
IP rating: IP 20
Protection class: II
Temperature range: - 25 °C - +55 °C
SingleUS/Dual US
)
2
)
2
3 x 10 m / 3 x 20 m (30 / 60 m²) max.
3 x 2.5 m / 3 x 5 m (7.5 / 15 m²) min.
- 22 -
Functions – Settings by DIP switch
COM 1 + COM 2
DIP 1
Normal mode / Test mode (NORM / TEST)
Test mode has priority over all ambient light level, the presence
other settings on the presence detector activates the light to
detector and serves the purpose stay ON for approx. 8 sec. in
of checking for proper working response to movement in the
order as well for testing the de- room. (blue LED flashes when
tection zone. Irrespective of movement is detected).
DIP 2
Semi-automatic mode (MAN) / fully automatic mode (AUTO)
Semi-automatic mode: (MAN)
The light now only switches Light must be requested using
OFF automatically. Light is the button and stays ON for the
switched ON manually. time set at the potentiometer
Fully automatic mode: (AUTO)
The light automatically switches matic switching function. Irre-
ON and OFF in relation to light spective of the settings selected,
level when someone is present. light stays ON for 4 hours after
Light can be switched ON and manually pressing the button
OFF manually at any time. This twice or switches OFF after man-
temporarily interrupts the auto- ually pressing the button once.
DIP 3
Button/switch
Tells the sensor how to interpret Operation either by button or
n
the incoming signal. Assigning
switch
external buttons/switches allows
Several buttons possible on
n
you to operate the detector as a one control input
semi-automatic unit and over-
Only use illuminated pushbut-
n
ride it manually at any time.
ton with neutral conductor
connected
DIP 4
ON/ON-OFF button
In the ON-OFF setting, the light pulse mode: no manual OFF).
can be switched ON and OFF In the ON setting, light can no
manually at any time (except in longer be switched OFF manual-
DIM
DIP 5
Constant light ON/OFF
Provides a constant level of el of brightness. As daylight
brightness. Detector measures changes, the switched-in artifi-
the prevailing level of daylight cial lighting component is ad-
and activates sufficient artificial justed accordingly. In addition to
the daylight component, artificial
light to achieve the required lev-
d
All user-selected potentiometer
settings apply in normal mode.
The presence detector can also
be set by means of the blue LED
without any load connected.
(pressing twice switches ON for
4 hours).
Pressing the button before the
4 hours elapse returns the pres-
ence detectors to the normal
operating mode.
Cable length between sensor
n
and switch < 50 m
ly. The stay-ON time starts from
the beginning again each time
the button is pressed.
light is also switched ON and OFF
in relation to whether or not per-
sons are present.
- 23 -