Automatic Power Off - Stihl ADVANCE ProCOM Bedienungsanleitung

GB
11. AMBIENT LISTENING (DEFAULT: DISABLE)
With the help of ambient listening you are able to hear
surround sounds even if you are wearing the earmuffs.
Harmful noises are automatically reduced as soon as they
appear. To enable or disable Ambient, tap the Mesh Button
twice or use the ADVANCE ProCOM App.
12. USING THE DMR RADIO DEVICE
A Bluetooth DMR radio device can be connected. Please
refer to "6. PAIRING THE HEADSET WITH BLUETOOTH
DEVICES" for details on DMR radio device pairing.
To use the DMR Radio device, press and hold the PTT
Button while you talk. Mesh Intercom is still working in
addition.
13. FUNCTION PRIORITY
The headset output is prioritised in the following order:
(highest) DMR radio device
Mesh Intercom
Phone call
(lowest) Bluetooth stereo music / FM radio
NOTE: When a DMR Radio device is connected to second
Bluetooth pairing place,
• you cannot listening to Bluetooth stereo music and FM radio.
• the DMR Radio device will be disconnected during a phone
call and reconnected automatically after the phone call.

14. AUTOMATIC POWER OFF

If no button is pressed for about 4 hours, the power is
automatically turned off.
15. CONFIGURING YOUR HEADSET
You can change the settings of the headset through the
ADVANCE ProCOM App or the STIHL Device Manager.
15.1 Headset Language
You can select the headset language. The selected
language is maintained even when the headset is
rebooted.
15.2 Microphone Sensitivity (Default: 3)
You can adjust the sensitivity of the mic depending of your
voice level or surround noise level. If your speech level or
the surround noise level is very loud, please use level 1. If
your speech level is low, please use a higher level.
15.3 Audio Overlay Volume Management (Default: Enable)
The volume of the music and radio is reduced when you
communicate. This helps for better understanding the
conversation.
15.4 Sidetone (Default: Enable)
Sidetone is audible feedback of your own voice. It helps
you to naturally speak at the correct level according to
varying headset noise conditions. If this feature is enabled,
you can hear what you are speaking during an intercom
conversation or a phone call. If you do not hear a side
tone, your mic is muted.
The previous sidetone settings will remain intact even after
the headset is rebooted.
15.5 RDS AF Setting (Default: Disable)
Radio Data System (RDS) Alternative Frequency (AF)
Setting allows a receiver to re-tune to the second
frequency location when the first signal becomes too weak.
With RDS AF enabled on the receiver, a radio station with
more than one frequency can be used.
15.6 FM Station Guide (Default: Enable)
When FM Station Guide is enabled, FM station frequencies
are given by voice notifications as you select preset
stations. When FM Station Guide is disabled, the voice
notifications on FM station frequencies will not be given as
you select preset stations.
15.7 Region Selection (Table P)
You can select the proper FM frequency range for your
location from the ADVANCE ProCOM App or the STIHL
Device Manager. Using the region setting, you can
optimise the seek function to avoid unnecessary frequency
ranges.
15.8 Factory Reset
If you want to restore the headset to factory default
settings, use the Factory Reset menu on the ADVANCE
ProCOM App. The headset automatically restores the
default settings and turns off.
16. TROUBLESHOOTING
16.1 Fault Reset (Please see Figure 3)
When the headset is not working properly, you can easily
reset the unit:
1. Remove the ear cushion of the left earmuff by sliding
your fingers under the inner edge of the ear cushion and
firmly pulling it straight out.
2. Remove the sponge.
3. Locate the pinhole reset button inside the left ear cup.
4. Gently insert a paperclip into the hole and tap the
pinhole reset button with light pressure.
5. The headset will shut down.
6. Switch on the headset again by pressing and holding the
Multi-function Button for 2 seconds.
NOTE: Fault Reset will not restore the headset to factory
default settings.
20