Stihl ADVANCE ProCOM Bedienungsanleitung Seite 27

10.1 Open Mesh (Please see Figure 1)
Open Mesh is an open group intercom conversation.
Users can freely communicate with each other in the
same channel of Open Mesh. Entering the Open Mesh is
possible anytime. You can select a channel to use (1-9)
using the headset.
10.2 Group Mesh (Please see Figure 2)
You have the possibility to create groups with clearly
defined users with the use of ADVANCE ProCOM App.
10.3 Starting the Mesh Intercom
When you switch on the headset, the Mesh Intercom is
automatically enabled. When Mesh Intercom is enabled,
the headset will automatically connect to nearby ADVANCE
ProCOM users. You will hear a voice notification, "Mesh
Intercom On", "Open Mesh", and "Channel 1".
NOTE:
• The headset will be in Open Mesh (default: channel 1)
initially.
• An LED blinking slowly in green indicates the device is now
in Open Mesh.
10.4 Using the Mesh in Open Mesh
• Channel Setting (Default: channel 1)
If the Open Mesh communication experiences interference
because other groups are also using the channel 1
(default), change the channel. You can select one of 1 to
9 channels.
You can change the Channel Setting of the headset
through the ADVANCE ProCOM App.
10.5 Using the Mesh in Group Mesh
• Creating a Group Mesh
Creating a Group Mesh requires two or more Open Mesh
users.
1. The users must be located nearby in range of Mesh
Intercom.
2. With the help of the ADVANCE ProCOM App, Open
Mesh users can create a Group Mesh.
3. The Open Mesh users will hear a voice notification,
"Mesh Grouping".
4. When the headsets complete Mesh Grouping, users will
hear a voice notification, "Group Mesh". Headset will
automatically switch from Open Mesh to Group Mesh.
• Joining an Existing Group Mesh
One of the members in an Existing Group Mesh can allow
new members in Open Mesh to join the Existing Group
Mesh.
1. The users must be located nearby in range of Mesh
Intercom.
2. With the help of the ADVANCE ProCOM App, Open
Mesh users can create a Group Mesh.
3. The current member and new members will hear a voice
notification, "Mesh Grouping".
4. When the headsets complete Mesh Grouping, new
members will hear a voice notification, "Group Mesh".
The new members' headsets automatically switch from
Open Mesh to Group Mesh.
10.6 Toggling between Open Mesh and Group Mesh
You have two options to toggle between Open Mesh and
Group Mesh:
1. Pressing and holding the Mesh Button longer than
2 seconds
2. Using the App
This allows you to keep the Mesh Network connection
information while in Open Mesh. You can toggle to Group
Mesh to communicate with participants from the stored Mesh
Network connection information.
NOTE: If you have never participated in Group Mesh, you
cannot toggle between Open Mesh and Group Mesh. You
will hear a voice notification, "No Group Available".
10.7 Muting the Microphone (default: unmute)
You can mute or unmute your microphone during an
intercom conversation by tapping the Mesh Button. You will
hear a voice notification, "Mic on" or "Mic off".
NOTE: Although you have muted the microphone, you can
unmute it for Mesh Intercom communication by pressing
the PTT Button if the DMR radio device is not connected.
10.8 MESH Out of Range Signal
Whenever you leave the range of the current Open or
Group Mesh, you will hear four beeps every minute. You
can enable or disable MESH out of range signal through
the ADVANCE ProCOM App.
NOTE: If you get this signal please ensure to come back in
range of Mesh to communicate with the others.
10.9 Resetting the Mesh
You can reset the Mesh through the ADVANCE ProCOM
App. You will hear a voice notification, "Reset Mesh".
If a headset in an Open Mesh or Group Mesh resets the
Mesh, it will automatically return to Open Mesh (default:
channel 1).
NOTE: When you reset the Mesh, the stored Mesh network
information will be deleted.
19
GB