Accessories And Spare Parts - Stihl ADVANCE ProCOM Bedienungsanleitung

GB
1.4 Temperature Range (Table K)
(K:1) Operating temperature range
(K:2) Storage temperature range
(K:3) Charging temperature range
1.5 Approved Helmet Combinations (Table O)
(O:1) Helmet Brand
(O:2) Helmet Model
(O:3) Size Combination
(O:4) Helmet Mount Adaptor

2. ACCESSORIES AND SPARE PARTS

2.1 Accessories - Delivered with the Headset
(B:1) USB Power & Data Cable (USB-C)
(B:2) Microphone Sponge (2)
(B:3) Microphone
2.2 Spare parts - Getting Separate from the Dealer
(B:4) Hygiene Kit
- Cushion (2)
- Foam cushion (2)
- Microphone Sponge (2)
(B:5) Microphone
- Microphone Sponge (2)
- Microphone
3. INSTALLING THE HEADSET
3.1 Installing the Microphone
(C:1) Align the arrows on the headset and microphone and
insert the microphone.
(C:2) Fasten the microphone by rotating it anticlockwise.
NOTE:
• Ensure that the microphone is firmly fastened to the
headset.
• Removing the Microphone
- (D:1) Unfasten the microphone by rotating it clockwise.
- (D:2) Align the arrows on the headset and microphone
and remove the microphone.
• Do not use the headset without the microphone.
3.2 Installing ADVANCE ProCOM - with Adaptors for
Function Universal and ADVANCE X-Climb
(E:1) Rotate the helmet mount adaptors clockwise or
anticlockwise so that the earmuffs are facing the backside
of the helmet.
(E:2) Attach the earmuffs to each side of the hard hat by
sliding the helmet mount adaptors into the left and right
slots of the hard hat. The earmuff with the microphone
should be mounted on the left side of the hard hat (from
the wearer's view).
(E:3) Rotate the earmuffs downwards so that the earmuffs
fit over your ears.
(E:4) Work mode: Press the ear cup supporting arms
inwards until you hear a click on both sides. Ensure that
the ear cups and the ear cup supporting arms do not press
against the edge of the helmet when in work mode as this
can cause noise leakage. Position the microphone close
to your mouth.
(E:5) Stand-by position: Press the ear cup supporting arms
outwards until you hear a click on both sides.
NOTE:
• Ensure that the cable is laid correctly inside the helmet.
• Ensure that the hard hat adaptors are firmly mounted to
the helmet.
• A firm seal should be established before entering a noisy
environment.
• Do not store the helmet with the helmet attachment in stand-
by position. This causes stress on the helmet attachment.
• When the helmet is not in use, ensure that the ear cups are
left in parking position. This will decrease the stress on the
helmet attachment.
3.3 Installing ADVANCE ProCOM - with Adaptors for
ADVANCE Vent/X-Vent
(F:1) ADVANCE ProCOM - with Adaptors for ADVANCE
Vent/X-Vent is already installed to the helmet when open
the packaging. If the earmuffs have to be reinstalled for any
reasons please proceed as follows:
Push the hearing protectors' helmet attachment into the
helmet slot until it locks into position.
(F:2) Work mode: Press the ear cup supporting arms
inwards until you hear a click on both sides. Ensure that
the ear cups and the ear cup supporting arms do not press
against the edge of the helmet when in work mode as this
can cause noise leakage. Position the microphone close
to your mouth.
(F:3) Stand-by position: Press the ear cup supporting arms
outwards until you hear a click on both sides.
WARNING
These earmuffs attached to ADVANCE helmet are in the
'Large' size range. EN 352-3 earmuffs attached to head
protection are in the 'Medium Size Range', the 'Small Size
Range' or the 'Large Size Range'. Earmuffs in the 'Medium
size range' fit the majority of users. 'Small size range'
or 'Large size range' earmuffs are intended for users for
whom 'Medium size range' earmuffs are not suitable.
NOTE:
• Ensure that the cable is laid correctly inside the helmet.
• Ensure that the hard hat adaptors are firmly mounted to
the helmet.
• A firm seal should be established before entering a noisy
environment.
16