Inhaltsverzeichnis
Werbung
GB
d) Support large panels to minimise the risk of blade pinching and kickback. Large panels
tend to sag under their own weight. Supports must be placed under the panel on both
D
sides, near the line of cut and near the edge of the panel.
e) Do not use dull or damaged blades. Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade binding and kickback.
NL
f)
Blade depth and bevel adjusting locking levers must be tight and secure before making cut.
If blade adjustment shifts while cutting, it may cause binding and kickback.
g) Use extra caution when making a "plunge cut" into existing walls or other blind areas. The
F
protruding blade may cut objects that can cause kickback.
Safety instructions lower guard
E
a) Check lower guard for proper closing before each use. Do not operate the saw if lower
guard does not move freely and close instantly. Never clamp or tie the lower guard into the
open position. If saw is accidentally dropped, lower guard may be bent. Raise the lower
P
guard with the retracting handle and make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of cut.
b) Check the operation of the lower guard spring. If the guard and the spring are not operating
I
properly, they must be serviced before use. Lower guard may operate sluggishly due to
damaged parts, gummy deposits, or a build-up of debris.
c)
Lower guard should be retracted manually only for special cuts such as "plunge cuts" and
S
"compound cuts." Raise lower guard by retracting handle and as soon as blade enters the
material, the lower guard must be released. For all other sawing, the lower guard should
SF
operate automatically.
d) Always observe that the lower guard is covering the blade before placing saw down on
bench or floor.An unprotected, coasting blade will cause the saw to walk backwards,
N
cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch
is released.
DK
Before using the circular saw
•
Check the following points:
•
Does the voltage of the motor correspond with the mains voltage (appliances for a
mains voltage of 230 V
•
Are the mains lead and the mains plug in a good condition: solid, without any loose
ends or damage;
•
Is the saw blade missing any teeth or showing any cracks, it so must be replaced
immediately.
•
Make sure the blade is secure.
•
Use this circular saw to saw only wood, wood-like products.
•
Do not use circular saw blades wich are deformed or damaged.
•
Do not use HSS blades.
•
Only use blades meeting the required dimensions, as well as data and descriptions;
Never apply any blades of which the thickness is greater than that of the riving knife.
•
Do not stop the blade of a circular saw by pressing the blade from the side.
•
Check that the blade guard can freely move and fully closes.
•
Never lock-up the guard in the open position.
•
Never put sideward pressure on the blade. This may cause the blade to break.
•
Be careful when cutting wood with knots, nails or cracks in it and/or dirt on it, as these can
cause the blade to get stuck.
08
All manuals and user guides at all-guides.com
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til
at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammo-
niak, osv. Den slags stoffer beskadiger kunststofdelene.
Udskiftning af kulbørster
Fig. E
•
•
•
•
•
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Ferm
Ferm
•
Elektromotoren over-
•
Motoren overbelastes,
ophedes.
fordi der saves for
store arbejdsemner.
•
Motoren er defekt.
•
Maskinen virker ikke,
•
Fejl i netledningen.
selv om den er tilko-
blet.
•
Afbryderen er defekt.
•
Det er vanskeligt at
•
Savklingen er bøjet
føre arbejdsemnet i en
eller sløv.
ret linie langs savklin-
gen og savskæret er
uregelmæssigt.
•
Rundsaven støjer
•
Kulbørsterne er slidte.
og/eller går meget ure-
gelmæssigt.
Fjern skruerne (1).
Træk kulbørsterne (2) ud fra rundsaven og undersøg dem for slitage.
Sæt kulbørsterne tilbage i de forhåndenværende holdere.
Kontroller, at kobberkontakten på kulbørsterne er i god kontakt med kobberdelen i
børsteholderen.
Sæt skruerne (1) i igen og stram dem godt.
Efter mange driftstimer kan kulbørsterne være slidt. Derfor skal kulbørsterne
kontrolleres regelmæssigt efter hver 30 driftstimer. Hvis kulbørsterne er kortere
end 4 mm, skal de udskiftes med nye.
UK
•
Sav i et lavere tempo
og lad motoren køle af.
D
•
Kontakt venligst serv-
iceadressen på garanti-
NL
beviset.
•
Kontrollér netledningen
F
for brud.
•
Kontakt venligst serv-
E
iceadressen på garanti-
beviset.
P
•
Udskift savklingen.
I
S
•
Kontakt venligst serv-
iceadressen på garanti-
beviset.
SF
N
DK
117
Werbung
Inhaltsverzeichnis
