Specifications - Makita LH1040 Betriebsanleitung

ENGLISH
(Original instructions)
1 Auxiliary plate
2 Hex bolt(s)
3 Base
4 Nut
5 Holder
6 Adjuster
7 Screw
8 Lower blade guard A
9 Lower blade guard B
10 Top blade guard
11 Bolt
12 Handle
13 Lever
14 Socket wrench
15 Adjusting bolt
16 Top surface of turn base
17 Periphery of blade
18 Guide fence
19 Pointer
20 Lock lever
21 Grip
22 Miter scale
23 Bevel scale
24 Switch
25 Lamp switch
26 Lamps
27 Stopper pin
28 Clamping screw
29 Top table
30 Motor housing
31 Center cover

SPECIFICATIONS

Model
Blade diameter .................................................................................................................................. 255 mm – 260 mm
Blade body thickness............................................................................................................................ 1.6 mm – 2.4 mm
Hole diameter
For all countries other than European countries ........................................................................... 25.4 mm and 25 mm
For European countries ......................................................................................................................................30 mm
Max. Cutting capacities (H x W) with blade 260 mm in diameter in the miter saw mode
Bevel angle
0°
45° (left)
Max. Cutting capacities at 90° in the table saw (bench saw mode)....................................................................... 40 mm
–1
No load speed (min ) ............................................................................................................................................ 4,800
Table size (W x L) ............................................................................................................................... 260 mm x 405 mm
Dimensions (L x W x H) .....................................................................................................530 mm x 476 mm x 535 mm
Net weight ............................................................................................................................................................ 14.3 kg
Safety class .............................................................................................................................................................
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Explanation of general view
32 Blade guard A
33 Blade guard B
34 Shaft lock
35 Saw blade
36 Blade case
37 Arrow
38 Outer flange
39 Inner flange
40 Spindle
41 Ring
42 Riving knife
43 Area to press in
44 Blade width
45 Rip fence holder
46 Guide rail on the top table
47 Clamping screw (A)
48 Clamping screw (B)
49 Rip fence
50 Workpiece
51 Line to be aligned with
52 Square nut
53 Scale
54 Two screws
55 Washer
56 Dust nozzle
57 Dust bag
58 Fastener
59 Cap
60 Vacuum cleaner
61 Blade cover
62 Support
0°
69 mm x 130 mm
93 mm x 95 mm
35 mm x 130 mm
53 mm x 95 mm
63 Turn base
64 Vise arm
65 Vise rod
66 Holder assembly
67 Vise knob
68 Projection
69 Vise shaft
70 Rod 12
71 Vise (optional accessory)
72 Vise
73 Aluminum extrusion
74 Spacer block
75 Set plate
76 Small boss
77 Face/edge parallel
78 Wood screw
79 Glue together
80 Hole (7 mm in diameter)
81 Bolt M6
82 Push stick
83 Auxiliary fence
84 Push block
85 Triangular rule
86 0° adjusting bolt
87 Arm
88 45° bevel angle adjusting bolt
89 Limit mark
90 Screwdriver
91 Brush holder cap
Miter angle
right 69 mm x 85 mm, 93 mm x 67 mm
left 69 mm x 85 mm, 93 mm x 67 mm
right 35 mm x 91 mm, 49 mm x 67 mm
left 35 mm x 65 mm, 49 mm x 42 mm
LH1040/LH1040F
45°
/II
13