Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications - Makita LS1040 Betriebsanleitung

Gehrungs- und kappsäge
Vorschau ausblenden Andere Handbücher für LS1040:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 20
ENGLISH
1 Base
2 Hex bolt
3 Auxiliary plate
4 Nut
5 Bolt
6 Center cover
7 Socket wrench
8 Shaft lock
9 Loosen
0 Arrow
q Blade case
w Arrow
e Saw blade
r Spindle
t Flange
y Ring
u Flange
i Hex bolt
o Tighten
p Safety cover
a Dust spout
s Dust bag
d Fastener
f Lock-off button

SPECIFICATIONS

Model
Blade diameter .................................................................................................................... 255 mm — 260 mm
Hole (arbor) diameter
For all countries other than European countries ............................................................ 25.4 mm and 25 mm
For European countries ........................................................................................................................ 30 mm
Max. cutting capacities (H x W) with blade 260 mm in diameter
Bevel angle
45° (left)
No load speed (RPM) ................................................................................................................................ 4,600
Dimensions (L x W x H) ..................................................................................... 530 mm x 476 mm x 532 mm
Net weight .................................................................................................................................................. 11 kg
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
8
Explanation of general view
g Switch trigger
h Lever
j Turn base
k Kerf board
l Sub-fence
; Adjusting bolt
z Pointer
x Miter scale
c Latch spring
v Grip
b Lever
n Bevel scale
m Pointer
, Vise rod
. Screws
/ Guide fence
¡ Vise arm
™ Clamp screw
£ Support
¢ Knob
∞ Projection
§ Holder
¶ Screw
• Holder assembly
Miter angle
93 mm x 95 mm
69 mm x 135 mm
53 mm x 95 mm
35 mm x 135 mm
ª Screw
º Rod 12
œ Cutting line
∑ Groove
é Vise
® Spacer block
† Aluminum extrusion
¥ Spacer block
ü Over 10 mm
î Over 460 mm
ø Hole
π Set plate
å Screw
ß Triangular rule
∂ Hex bolts
ƒ Arm
© Hex bolt (A)
˙ Top surface of turn base
∆ Arm holder
˚ Hex bolt (B)
¬ Limit mark
... Screwdriver
Ω Brush holder cap
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.30 Ohms it can
be presumed that there will be no negative effects.
The mains socket used for this device must be
protected with a fuse or protective circuit breaker
having slow tripping characteristics.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
LS1040
45° (left and right)
93 mm x 67 mm
69 mm x 95 mm
49 mm x 67 mm
35 mm x 94 mm

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Ls1040n

Inhaltsverzeichnis