REMS Contact 2000 Betriebsanleitung Seite 5

g
Fig. 1
1 Prism electrode
2 Rod electrode
3 Switch
4 Tongs
Read all instructions. Failure to follow all instructions listed below may result in
listed below refers to your mains operated (corded) power tool or battery operated
(cordless) power tool, also machines and electric units. Only use the power tool for
he purpose for which it was intended, with the due attention to the general safety
and accident prevention regulations.
SAVE THESE INSTRUCTIONS.
A) Work area
may ignite the dust or fumes.
tions can cause you to lose control.
tool comes with an earthed wire, the plug may only be connected to an earthed
receptacle. At work sites, in damp surroundings, in the open or in the case of
comparable types of use, only operate the power tool off the mains using a 30
mA fault current protected switch (FI breaker).
if your body is earthed or grounded.
tool will increase the risk of electric shock.
parts. Damaged or entangled cords increase the risk of electric shock.
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
power tools may result in serious personal injury.
as dust mask, non skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
plugging in.
power tools that have the switch on invites accidents.
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
better control of the power tool in unexpected situations.
hair can be caught in moving parts.
can reduce dust related hazards.
operate he power tool when they are over 16, when this is necessary for their
training and when they are supervised by a trained operative.
The correct power tool will do the job better and safer at the rate for which it was
designed.
tool that cannot be controlled with the switch is dangerous and must be repaired.
ures reduce the risk of starting the power tool accidentally.
tool. Power tools are dangerous in the hands of untrained users.
5 Screws
6 Holder with prism electrode
7 Fillister head screw
Cluttered and dark areas invite accidents.
Power tools create sparks which
Distrac-
Unmod-
There is an increased risk of electric shock
Water entering a power
A moment of inattention while operating
Safety equipment such
This enables
Loose clothes, jewellery or long
Use of these devices
Apprentices may only
Any power
Such preventive safety meas-
accidents are caused by poorly maintained power tools.
sharp cutting edges are less likely to bind and are easier to control.
Use clamps or a vice to hold the workpiece. This is safer
than holding it with your hand, and also it frees both hands to operate the equip-
ment.
Use of the power tool for operations different from those intended could result in
prohibited for safety reasons.
E) Service
is maintained.
-
The electrodes reach a working temperature of around 900°C – so never touch
either the electrodes or the front of the tongs or the work piece, whether during
or alter soldering!
When putting down he tongs after soldering, ensure that the front part of the
Change worn electrodes and electrode holders.
Persons (including children) whose
– physical, sensory or mental abilities or
– lack of experience and knowledge
do not allow safe operation of the device without supervision or instruction may
not use the device.
Children may not be allowed to play with the device.
-
Only use REMS Contact 2000 for the intended purpose of soft soldering of copper
pipes.
All o her uses are not for the intended purpose and are prohibited.
Read the operating instructions before use
-
Power tool complies with protection class I
Power tool complies with protection class II
Environmentally friendly disposal
A
Electric soldering unit REMS Contact 2000
Prisma electrodes with holder
Prisma electrodes
Rod electrodes
REMS Lot Cu 3
REMS Paste Cu 3
1.2. Working range
Soft soldering of hard and soft copper piping
1.3. Electrical data
Rated power input
Rated voltage (mains voltage)
Rated frequency
Rated current
Mains fuse
Control voltage
Secondary no-load voltage
Secondary rated voltage
Secondary rated current
Shutoff operation AB
Secondary overload protection by temperature switch
Length × width × height
Properly maintained cutting tools with
This will ensure that the safety of he power tool
(pair)
(pair)
(pair)
210 × 150 × 140 mm
g
Many
-
164011
164110
164111
164115
160200
160210
6 – 54 mm
2000 VA
230 V
50 – 60 Hz
8.7 A
10 A
24 V AC
7 V AC
7 V AC
250 A AC
0.5 / 3 min
5