Scheppach bgs 700 Original Bedienungsanleitung Seite 20

16. Avoid unintentional starting
Don't carry plugged-in tool with finger on switch.
Be sure switch is off when plugging in.
17. Outdoor use extension cords
When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
18. Stay alert
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
19. Check damaged parts
Before further use of the tool, a guard or other
part that is damaged should be carefully checked
to determine that it will operate properly and per-
form its intended function. Check for alignment of
moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that
may affect its operation. A guard or other part
that is damaged should be properly repaired or
replaced by an authorized service-center unless
otherwise indicated elsewhere in this instructions
manual. Have defective switches replaced by
an authorized service-center. Do not use tool if
switch does not turn it on and off
20. m Warning!
The use of any other accessory or attachment
other than recommended it this operating instruc-
tion or the catalogue may present a risk of per-
sonal injury.
21. Have your tool repaired by an expert. This
electric appliance is in accordance with the rel-
evant safety rules repairing of electric appliances
may be carried out only by experts otherwise it
may cause considerable danger for the user.
22. Connect the dust extraction device
Wherever there are facilities for fitting a dust ex-
traction system, make sure it is connected and
used.
General safety regulations and accident preven-
tion
It is essential that you read the safety regulations and
operating instructions in their entirety and follow the
information contained therein in order to eliminate the
possibility of an accident or potentially dangerous sit-
uation from occurring while working with the machine.
• Always check the device, the mains cable and the
plug before using the device. Only operate the tool
when it is in good working order and is not dam-
aged in any way. Damaged parts have to be re-
placed immediately by a qualified electrician.
• Always pull the power plug out of the socket out-
let before doing any work on the machine, before
changing tools and whenever the machine is not
being used.
• To prevent damage to the power cable, always lead
the power cable away from the rear of the machine.
• Keep the tools in a safe place and out of the reach
of children.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Use on materials containing asbestos is prohib-
ited.
Note the corresponding accident prevention regula-
tion issued by the professional associations in your
country.
• Use only original replacement parts.
• Repairs may only be carried out by a qualified elec-
trician.
• The machine may exceed 91.5 dB at the workplace.
The operator will require noise protection meas-
ures and ear muffs if this is the case. The noise
of this electric tool is measured in accordance with
IEC 59 CO 11, IEC 704, DIN 45635 part 21, NFS
31-031 (84/537/EEC).
• Ensure that you maintain a steady foothold. Avoid
abnormal working postures.
• Do not expose your electric tool to rain. Never use
electric tools in damp or wet locations or near flam-
mable liquids or gases.
• Protect the mains cable from becoming damaged
by oil, solvents and sharp edges.
• Keep your work area tidy.
• Make sure that the switch is turned off when con-
necting the tool to the power supply.
• Wear suitable work clothes. Never wear loose fit-
ting clothes and jewellery. Wear a hair net if you
have long hair.
• For your own safety, use only accessories and
auxiliary equipment from the manufacturer of your
electric tool.
• Always wear safety goggles, protective gloves and
ear-muffs while carrying out grinding, brushing and
cutting jobs.
• Check that the rotating speed shown on the wheel
is equal to or higher than the rated speed of rotation
for the tool.
• Make sure that the grinding wheel is of the correct
size for the grinder.
• Grinding wheels must be handled and stored with
care in accordance with the manufacturer's instruc-
tions. Examine the grinding wheel each time be-
fore using it. Never use grinding wheels which have
parts broken off or are cracked or in any other way
damaged.
• Be sure to use only grinding wheels and brushes
which are marked with a speed at least as high as
the speed indicated on the rating plate of the elec-
tric tool.
• Check that grinding wheels are fitted in accordance
with the manufacturer's instructions.
• Make sure that intermediate layers are used if they
are supplied with and required for the grinding
wheel.
• Make sure that the grinding disk is correctly fitted
and secured before you start to use the tool. Allow
the machine to run without load and in a safe posi-
tion for 5 minutes.