Operation - EINHELL EHM 1300 Bedienungsanleitung

Anleitung EHM_1300_SPK1:_

10. Operation

Important: The surfacing and thicknessing plane
has been specially designed for planing solid wood.
High alloy knives (21) are used for this purpose. The
contact surface of the workpiece must be flat for
thicknessing. If you wish to plane large or heavy
workpieces, the machine must be secured in place
(for example using screw clamps).
The ON/OFF switch (1) is on the left-hand side of
the machine under the yellow hinged cover.
Press the green key "I" to switch on the machine.
Press the red key "0" to switch off the machine.
The machine is fitted with an overload switch
(35) to protect the motor. In the event of an
overload, the machine will cut out automatically.
After a short time, the overload switch (35) can
be reset again.
11. Surfacing
11.1 Adjustment (Fig. 1/3/4)
Turn the adjustment knob for cutting depth (9)
to set the height of the feed table (13). The set
cutting depth can be read off the scale (18).
Loosen the parallel stop (6) with the clamp lever
(7). Set the required angle. The set angle can be
read off the scale (19). Secure the parallel stop
(6) with the clamp lever (7) again after making
the setting.
11.2 Fitting the chip extractor (Figure 6/7/14)
Fit the hand crank (4) to the post on the planing
table (14). Turn the hand crank (4) counter-
clockwise to move the thicknessing table (20) to
its lowest position.
Place the chip extractor (5) on the thicknessing
table (20). Ensure that the three stop journals on
the chip extractor (5) engage in the three holes
on the thicknessing table (20).
Turn the crank handle (4) clockwise until the chip
extractor (5) is firmly secure and the recess (b) is
on the safety switch. Secure the chip extractor
(5) on the thicknessing table (20) using the nut
supplied (a), as shown in Figure 7.
Fit the 100 mm chip extractor adapter (27) and, if
necessary, the 35 mm chip extractor adapter
(28) to the chip extractor (5).
Connect the plane to a chip extraction system
(not supplied).
Raise the planing knife cover (12).
18.12.2006 8:20 Uhr Seite 13
11.3 Surfacing mode (Figure 1/8/9)
Connect the mains plug to the mains lead. Open
the yellow cover (1) and press the green button
"I" to start the plane.
Place the workpiece you wish to plane on the
feed table (13). Hold the slide blocks (2) with
both hands and slide the workpiece forwards
towards the planing table (14) over the knives
(21).
When you have finished work, switch off the
machine. To do this, press the red button "0" and
close the yellow cover (1). Then disconnect the
machine from the mains supply.
Remove the chips and dust from the feed table
(13), planing table (14) and knife block (23) after
the machine has reached a complete
standstill.
Return the planing knife cover (12) to its original
position.
12. Thicknessing
12.1 Adjustment (Fig. 10)
Place the hand crank (4) on the post on the
planing table (14) and turn it to adjust the
thicknessing table (20) to the required height.
The set angle can be read off the scale (29).
12.2 Fitting the chip extractor (Figure 1/10/14)
Undo the locking knob (32) and pull the planing
knife cover (12) forwards as far as possible.
Place the chip extractor (5) on the planing table
(14). Ensure that the stop pins and the securing
screw (34) are in the appropriate holes and are
engaged in the internal threads on the planing
table (14) and that the recess (b) is on the safety
switch.
Turn the locking knob (c) until the chip extractor
(5) is secure.
Fit the 100 mm chip extractor adapter (27) and, if
necessary, the 35 mm chip extractor adapter
(28) to the chip extractor (5).
Connect the plane to a chip extraction system
(not supplied).
12.3 Surfacing mode (Figure 11/13)
Connect the mains plug to the mains lead. Open
the yellow cover (1) and press the green button
"I" to start the plane.
Place a workpiece on the thicknessing table (20).
Guide the workpiece towards the feed table (13).
When you have finished work, switch off the
machine. To do this, press the red button "0" and
close the yellow cover (1). Then disconnect the
machine from the mains supply.
GB
13