Noise Emission Values; Technical Data; Before Starting The Machine - EINHELL EHM 1300 Bedienungsanleitung

Anleitung EHM_1300_SPK1:_
GB
Workpieces may kick back if the machine is used
incorrectly.
Damage to hearing and eye injuries plus injuries
to fingers and hands if the required protective
equipment is not used.
Harmful emissions when used in enclosed areas
without a suitable extractor system.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

6. Noise emission values

Sound pressure level L 92.9 dB(A)
pA
Sound power level L 105.9 dB(A)
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and
immission levels it is impossible to draw any certain
conclusions as to the need for additional
precautions. Factors with a potential influence on
the actual immission level at the workplace include
the duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machines
and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.

7. Technical data

AC motor: 230 V ~ 50 Hz
Power P:
Protection type:
Max. workpiece width:
Max. workpiece height at thickness opening: 100 mm
Surfacing plane table: 650 x 160 mm
Thicknessing table: 250 x 152 mm
Thicknessing feeding speed:
Idle speed of motor n : 21000 rpm
0
Idle speed of planing knives:
Max. planing cross-cutting depth:
Max. thicknessing cross-cutting depth:
12
18.12.2006 8:20 Uhr
Max. angle of the parallel stop:
Sawdust extractor:
Weight:

8. Before starting the machine

Unpack the surfacing and thicknessing plane and
examine it for any transit damage.
The machine has to be set up and aligned where
it can stand securely.
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the planing knife to run
freely.
When working with wood that has been
Idle speed
processed before, watch out for foreign bodies
such as nails or screws, etc.
Before you press the ON/OFF switch (1), make
sure that the planing knife is fitted correctly and
that the machine's moving parts run smoothly.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
9. Assembly
9.1 Parallel stop (Figure 4/5)
Place the knife cover plate (25) on the feed table
(13) as shown in Figure 5.
Place the parallel stop (6) on the feed table (13).
Ensure that the holes in the parallel stop (6) and
the knife cover plate (25) line up with the internal
threads in the feed table (13).
Secure the parallel stop (6) to the feed table (13)
using the two Allen screws supplied.
9.2 Planing knife cover (Figure 1-3)
Place the holder for the planing knife cover (8)
1280 W
on the left-hand side of the planing table (14) so
that the pin and grub screw engage in the two
IP20
holes.
152 mm
Secure the planing knife cover (12) using the
locking knob (33) supplied
9.3 Rubber feet/Tipping guard bar (Figure 1-2)
Secure the four rubber feet (11) to the underside
8 m/min
of the machine using the Allen screws supplied.
Screw the four tipping guard bars (26) into the
9000 rpm
internal threads provided and secure them with
the nuts supplied.
3 mm
2 mm
Seite 12
45°
Ø 100/35 mm
27.5 kg