Operation; Transport; Storage; Care And Service - Kärcher NT 50/2 Me Classic Betriebsanleitung

Installing the membrane filter
1. Unlock and remove the suction head.
2. Pull the membrane filter (special accessory) over
the edge of the container and ensure that it is fitted
correctly.
Illustration D
3. Fit and lock the suction head.
Wet vacuum cleaning
● When wet vacuum cleaning, the cartridge filter can
be replaced by a coarse dirt filter (special accesso-
ry) or a membrane filter (special accessory).
ATTENTION
Danger from wet substances
Risk of damage to the suction motor.
Make sure that either the cartridge filter, a coarse dirt fil-
ter (special accessory) or a membrane filter (special ac-
cessory) is used for wet vacuum cleaning.
● The fleece filter bag (special accessory) must al-
ways be removed when vacuuming wet substances.
● On completion of wet vacuum cleaning: Clean the
float and container with a damp cloth and dry.
Installing the coarse dirt filter
● When changing from wet to dry vacuuming, replace
the coarse dirt filter with a cartridge filter and a mem-
brane filter if applicable.
1. Unlock and remove the suction head.
2. Unscrew the star screw and pull off the cartridge fil-
ter.
3. Install the coarse dirt filter (special accessory).
Illustration E
4. Tighten the star screw.
5. Fit and lock the suction head.
Installing the membrane filter
- see dry vacuuming -
Draining the waste water
Only NT 70/2, NT 90/2:
WARNING
Improper disposal of waste water
Environmental pollution
Observe the local waste water treatment regulations.
1. Drain the waste water via the drain hose.
Illustration F
Clip connection
The suction hose is equipped with a clip system. All ac-
cessory parts with a nominal width of 40 mm can be
connected.
Illustration G

Operation

Switching on the device
1. Connect the mains plug.
2. Switch on the device.
Cleaning mode
1. Perform cleaning.
Draining the dirt receptacle
● The suction duct is equipped with a float.
● When the maximum permissible waste water level
in the container is reached, the suction volume is in-
terrupted.
1. Switch off the device.
2. Empty the container.
10
Switching off the device
1. Switch off the device.
2. Pull out the mains plug.
Each time after use
1. Empty the container.
2. Vacuum off the inside and outside of the device and
clean with a moist cloth.
Storing the device
1. Store the floor nozzles, suction pipe, suction hose,
angle piece, crevice nozzle and mains cable as
shown in the illustration.
Illustration H
2. Store the device in a dry room and secure it against
unauthorised use.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Push the device via the push handle when trans-
porting over longer distances.
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during storage.
The device may only be operated indoors.

Care and service

DANGER
Danger of electric shock
Injuries due to touching live parts
Switch off the device.
Remove the mains plug.
Changing the cartridge filter
1. Unlock and remove the suction head.
2. Unscrew star screw, remove cartridge filter and re-
place with a new one.
3. Tighten the star screw.
4. Fit and lock the suction head.
1. Unlock and remove the suction head.
2. Unscrew the star screw and pull off the cartridge fil-
ter.
3. Clean the float with a damp cloth.
4. Connect the cartridge filter.
5. Tighten the star screw.
6. Fit and lock the suction head.
English

Transport

Storage

Cleaning the float